Yamaha DM2000 Owner's Manual - Page 345

Format Details 331 When this is received, the corresponding effect's function activates (depending on the effect type). STATUS ID No. SUB STATUS GROUP ID MODEL ID ADDRESS DATA EOX 11110000 F0 01000011 43 0001nnnn 1n 00111110 3E 00000110 7F 00010010 12 0000aaaa 0a 00000000 00 0ddddddd dd 00000000 00 0ddddddd dd 11110111 F7 System exclusive message Manufacture's ID number (YAMAHA) n=0-15 (Device number=MIDI Channel) MODEL ID (digital mixer) Universal Function call Event Function Release:0, Press:1 Destination Effect Number 0 - 7 End of exclusive function Freeze Play button Freeze Record button Auto Pan 5.1 Trigger Button Auto Pan 5.1 Reset Button 0x00 0x01 0x02 0x03 Channel 0:Effect1-7:Effect8 0:Effect1-7:Effect8 0:Effect1-1:Effect2 0:Effect1-1:Effect2 • This does not activate when the effect type is different. 12.3.20 Parameter change (Key remote) Reception This is received if [Parameter change RX] is ON and the [Rx CH] matches the device number included in the SUB STATUS. This is echoed if [Parameter change ECHO] is ON. When this is received, the same processing that is executed when the key specified by Address is pressed (released). (Refer to the PARAMETER CHANGE PARAMETER NUMBER LIST.) Transmission If [Parameter Change ECHO] is ON, this message is retransmitted without change. STATUS ID No. SUB STATUS GROUP ID MODEL ID ADDRESS DATA EOX 11110000 F0 01000011 43 0001nnnn 1n 00111110 3E 00000110 06 00100000 20 0aaaaaaa aa 0aaaaaaa aa 0aaaaaaa aa 0ddddddd dd 11110111 F7 System exclusive message Manufacture's ID number (YAMAHA) n=0-15 (Device number=MIDI Channel) MODEL ID (digital mixer) DM2000 Address UU Address UL Address LU Address LL 0:press, 1:release End of exclusive 12.3.21 Parameter change (Remote Meter) When transmission is enabled by receiving a Request of Remote meter, the specified meter information is transmitted every 50 msec for 10 seconds. When you want to transmit meter information continuously, a Request must be transmitted continuously within every 10 seconds. Reception This is echoed if [Parameter change ECHO] is ON. Transmission When transmission has been enabled by a Request, the parameter specified by Address (see PARAMETER CHANGE PARAMETER NUMBER LIST) will be transmitted on the [Rx CH] channel at 50 msec intervals for a duration of 10 seconds. Transmission will be disabled if the power is turned off and on again, or if the PORT setting is changed. If [Parameter Change ECHO] is ON, this message is retransmitted without change. STATUS ID No. SUB STATUS GROUP ID MODEL ID ADDRESS DATA 11110000 F0 01000011 43 0001nnnn 1n 00111110 3E 00000110 06 00100001 21 0aaaaaaa aa 0aaaaaaa aa 0aaaaaaa aa 0ddddddd dd System exclusive message Manufacture's ID number (YAMAHA) n=0-15 (Device number=MIDI Channel) MODEL ID (digital mixer) DM2000 Address UU Address UL Address LU Address LL Data1 H 0ddddddd dd Data1 L : EOX 11110111 F7 End of exclusive Meter data uses the unmodified DECAY value of the DSP. For the interpretation of the value, refer to the PARAMETER CHANGE PARAMETER NUMBER LIST. 12.3.22 Parameter request (Remote Meter) Reception This is received if [Parameter change RX] is ON and the [Rx CH] matches the device number included in the SUB STATUS. This is echoed if [Parameter change ECHO] is ON. When this is received, the parameter specified by Address (refer to PARAMETER CHANGE PARAMETER NUMBER LIST) will be transmitted on the [Rx CH] at 50 msec intervals for a duration of 10 seconds. If Address UL= 0x7F is received, transmission of all meter data will be halted immediately. (disable) Transmission If [Parameter Change ECHO] is ON, this message is retransmitted without change. STATUS 11110000 F0 System exclusive message ID No. 01000011 43 Manufacture's ID number (YAMAHA) SUB STATUS 0011nnnn 3n n=0-15 (Device number=MIDI Channel) GROUP ID 00111110 3E MODEL ID (digital mixer) MODEL ID 00000110 06 DM2000 ADDRESS 00100001 21 Address UU 0aaaaaaa aa Address UL 0aaaaaaa aa Address LU 0aaaaaaa aa Address LL DATA 0cccccccccc Count H 0ccccccccCc Count L EOX 11110111 F7 End of exclusive 12.3.23 Parameter change (Remote Time Counter) When transmission is enabled by receiving a Request of Remote Time Counter, the Time Counter data is transmitted every 50 msec for 10 seconds. When you want to transmit Counter information continuously, a Request must be transmitted within every 10 seconds. Reception This is echoed if [Parameter change ECHO] is ON. Transmission When transmission is enabled by receiving a Request, the Time Counter information is transmitted on [RxCH] channel every 50 msec for 10 seconds. Transmission will be disabled if the power is turned off and on again, or if the PORT setting is changed. If [Parameter Change ECHO] is ON, this message is retransmitted without change. STATUS 11110000 F0 System exclusive message ID No. 01000011 43 Manufacture's ID number (YAMAHA) SUB STATUS 0001nnnn 1n n=0-15 (Device number=MIDI Channel) GROUP ID 00111110 3E MODEL ID (digital mixer) MODEL ID 00000110 06 DM2000 ADDRESS 00100001 22 Remote Time Counter 0000tttt 0t 0:Time Code, 1: Measure, Beat, Clock DATA 0ddddddd dd Hour / Measure H 0ddddddd dd Min / Measure L 0ddddddd dd Sec / Beat 0ddddddd dd Frame / Clock EOX 11110111 F7 End of exclusive 12.3.24 Parameter request (Remote Time Counter) Reception This is received if [Parameter change RX] is ON and the [Rx CH] matches the device number included in the SUB STATUS. This is echoed if [Parameter change ECHO] is ON. When this is received, the Time Counter information is transmitted on the [Rx CH] channel every 50 msec for 10 seconds. When the second byte of Address is received on 0x7F, data transmission will be halted immediately. Transmission If [Parameter Change ECHO] is ON, this message is retransmitted without DM2000-Owner's Manual