HP Xw6600 HP xw6600 Workstation Service and Technical Reference Guide - Page 104

Installing SATA hard drives in an optical drive bay (optional),

Get HP Xw6600 - Workstation - 2 GB RAM PDF manuals and user guides
UPC - 883585731121
View all HP Xw6600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

7. Choose from the following: ● For a single SATA drive, connect the SATA 0 data cable from the hard drive to the SATA0 port in the workstation chassis, as shown in the following figure. ● For a second SATA drive, connect the SATA 1 data cable from the hard drive to the SATA1 port in the workstation chassis. Figure 4-53 Connecting the SATA data cable to the workstation SATA port To install three or four SATA drives, install the third and fourth drives in the workstation optical bays. For instructions, see Installing SATA hard drives in an optical drive bay (optional) on page 94. Installing SATA hard drives in an optical drive bay (optional) 1. Disconnect power from the system (see Predisassembly procedures on page 52). 2. Remove the side access panel (see Side access panel on page 58). 3. Remove the front bezel (see Removing the front bezel on page 61). 4. If necessary, remove the EMI shield from the optical bay in which it will be installed. 94 Chapter 4 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
7.
Choose from the following:
●
For a single SATA drive, connect the SATA 0 data cable from the hard drive to the SATA0
port in the workstation chassis, as shown in the following figure.
●
For a second SATA drive, connect the SATA 1 data cable from the hard drive to the SATA1
port in the workstation chassis.
Figure 4-53
Connecting the SATA data cable to the workstation SATA port
To install three or four SATA drives, install the third and fourth drives in the workstation optical bays.
For instructions, see
Installing SATA hard drives in an optical drive bay (optional)
on page
94
.
Installing SATA hard drives in an optical drive bay (optional)
1.
Disconnect power from the system (see
Predisassembly procedures
on page
52
).
2.
Remove the side access panel (see
Side access panel
on page
58
).
3.
Remove the front bezel (see
Removing the front bezel
on page
61
).
4.
If necessary, remove the EMI shield from the optical bay in which it will be installed.
94
Chapter 4
Removal and replacement procedures
ENWW