HP Xw6600 HP xw6600 Workstation Service and Technical Reference Guide - Page 95

Removing a PCI card, Installing a PCI card, CAUTION

Get HP Xw6600 - Workstation - 2 GB RAM PDF manuals and user guides
UPC - 883585731121
View all HP Xw6600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Removing a PCI card To remove a PCI card: 1. Disconnect power from the system (see Predisassembly procedures on page 52). 2. Remove the side access panel (see Side access panel on page 58). 3. Remove the PCI card support bracket, if installed (see PCI card support bracket on page 80). 4. Remove auxiliary power or connector cables attached to the PCI card to be removed. 5. Open the PCI card retention clamp, press the retention clamp levers down to unsnap, and then rotate them up (1), as shown: Figure 4-39 Removing a PCI card 6. Pull the PCI card up and out of the chassis (2). Store the card in an anti static bag. CAUTION: To prevent possible heat damage to equipment if the workstation is powered up before replacing or reinstalling a removed PCI card, install a blank PCI slot cover in its place to maintain workstation chassis air flow integrity, then close the PCI retention clamp. If the PCI retention clamp levers do not readily close, verify that all cards are properly seated, and then try again. Remember to reinstall the workstation side access panel (see Side access panel on page 58). Installing a PCI card To install a PCI card: 1. Disconnect power from the system (see Predisassembly procedures on page 52). 2. Remove the side access panel (see Side access panel on page 58). 3. Remove the PCI card support bracket, if installed (see PCI card support bracket on page 80). ENWW Removing and replacing components 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
Removing a PCI card
To remove a PCI card:
1.
Disconnect power from the system (see
Predisassembly procedures
on page
52
).
2.
Remove the side access panel (see
Side access panel
on page
58
).
3.
Remove the PCI card support bracket, if installed (see
PCI card support bracket
on page
80
).
4.
Remove auxiliary power or connector cables attached to the PCI card to be removed.
5.
Open the PCI card retention clamp, press the retention clamp levers down to unsnap, and then
rotate them up (1), as shown:
Figure 4-39
Removing a PCI card
6.
Pull the PCI card up and out of the chassis (2). Store the card in an anti static bag.
CAUTION:
To prevent possible heat damage to equipment if the workstation is powered up
before replacing or reinstalling a removed PCI card, install a blank PCI slot cover in its place to
maintain workstation chassis air flow integrity, then close the PCI retention clamp.
If the PCI retention clamp levers do not readily close, verify that all cards are properly seated, and
then try again. Remember to reinstall the workstation side access panel (see
Side access panel
on page
58
).
Installing a PCI card
To install a PCI card:
1.
Disconnect power from the system (see
Predisassembly procedures
on page
52
).
2.
Remove the side access panel (see
Side access panel
on page
58
).
3.
Remove the PCI card support bracket, if installed (see
PCI card support bracket
on page
80
).
ENWW
Removing and replacing components
85