HP Xw6600 HP xw6600 Workstation Service and Technical Reference Guide - Page 73

Front panel I/O device assembly

Get HP Xw6600 - Workstation - 2 GB RAM PDF manuals and user guides
UPC - 883585731121
View all HP Xw6600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

3. Remove the bezel blanks by squeezing in on the tabs (1) and simultaneously pushing the bezel blanks out (2), as shown: Figure 4-11 Removing the bezel blanks 4. Remove the bezel blank by applying outward pressure on the subpanel (1) and pulling the blank away (2). A bezel blank has a hook on both sides. It is symmetric and can be installed upside down without issue. To replace a blank, align its hook on one side with the slot in the bezel, then rotate it until it snaps into place. Front panel I/O device assembly This section describes how to remove and install a front panel I/O device assembly. Removing the front panel I/O device assembly To remove the front panel I/O device assembly: 1. Disconnect power from the system (see Predisassembly procedures on page 52). 2. Remove the side access panel (see Side access panel on page 58). 3. Remove the front bezel (see Removing the front bezel on page 61). ENWW Removing and replacing components 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
3.
Remove the bezel blanks by squeezing in on the tabs (1) and simultaneously pushing the bezel
blanks out (2), as shown:
Figure 4-11
Removing the bezel blanks
4.
Remove the bezel blank by applying outward pressure on the subpanel (1) and pulling the blank
away (2).
A bezel blank has a hook on both sides. It is symmetric and can be installed upside down without
issue. To replace a blank, align its hook on one side with the slot in the bezel, then rotate it until it
snaps into place.
Front panel I/O device assembly
This section describes how to remove and install a front panel I/O device assembly.
Removing the front panel I/O device assembly
To remove the front panel I/O device assembly:
1.
Disconnect power from the system (see
Predisassembly procedures
on page
52
).
2.
Remove the side access panel (see
Side access panel
on page
58
).
3.
Remove the front bezel (see
Removing the front bezel
on page
61
).
ENWW
Removing and replacing components
63