HP Xw6600 HP xw6600 Workstation Service and Technical Reference Guide - Page 72

Replacing the front bezel, Bezel blanks, Removing bezel blanks

Get HP Xw6600 - Workstation - 2 GB RAM PDF manuals and user guides
UPC - 883585731121
View all HP Xw6600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

2. Lift the two release snaps located on the front bezel (1), as shown in the following figure: Figure 4-10 Removing the front bezel 3. Rotate the front bezel away from the chassis to remove the bezel (2). Replacing the front bezel To replace the front bezel, engage the three small hooks protruding on one side of the front bezel with matting holes on the workstation chassis and rotate the front bezel against the chassis front until the bezel snaps into place. Bezel blanks This section describes how to remove bezel blanks Removing bezel blanks To remove bezel blanks: 1. Disconnect power from the system (see Predisassembly procedures on page 52). 2. Remove the front bezel (see Removing the front bezel on page 61). 62 Chapter 4 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
2.
Lift the two release snaps located on the front bezel (1), as shown in the following figure:
Figure 4-10
Removing the front bezel
3.
Rotate the front bezel away from the chassis to remove the bezel (2).
Replacing the front bezel
To replace the front bezel, engage the three small hooks protruding on one side of the front bezel with
matting holes on the workstation chassis and rotate the front bezel against the chassis front until the
bezel snaps into place.
Bezel blanks
This section describes how to remove bezel blanks
Removing bezel blanks
To remove bezel blanks:
1.
Disconnect power from the system (see
Predisassembly procedures
on page
52
).
2.
Remove the front bezel (see
Removing the front bezel
on page
61
).
62
Chapter 4
Removal and replacement procedures
ENWW