HP Xw6600 HP xw6600 Workstation Service and Technical Reference Guide - Page 82

Power supply, Removing the power supply, Reinstalling or replacing the power supply

Get HP Xw6600 - Workstation - 2 GB RAM PDF manuals and user guides
UPC - 883585731121
View all HP Xw6600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Power supply This section describes how to remove the power supply. Removing the power supply To remove the power supply: 1. Disconnect power from the system (see Predisassembly procedures on page 52). 2. Remove the side access panel (see Side access panel on page 58). 3. To ease installation of the power supply, write down the numbers on the cables so you can easily reconnect them to the correct devices. 4. Remove the memory fan and chassis fan assemblies. 5. Disconnect cables from the system board, drives, and cards. 6. Remove the four screws from the back panel (1), as shown: Figure 4-23 Removing the power supply 7. Slide the power supply toward the front of the chassis and lift it out of the chassis (2). Reinstalling or replacing the power supply To install the power supply, reverse the steps completed for removal. CAUTION: To prevent possible equipment damage, see Power connections on page 73 to ensure proper connection of power supply cables. 72 Chapter 4 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
Power supply
This section describes how to remove the power supply.
Removing the power supply
To remove the power supply:
1.
Disconnect power from the system (see
Predisassembly procedures
on page
52
).
2.
Remove the side access panel (see
Side access panel
on page
58
).
3.
To ease installation of the power supply, write down the numbers on the cables so you can easily
reconnect them to the correct devices.
4.
Remove the memory fan and chassis fan assemblies.
5.
Disconnect cables from the system board, drives, and cards.
6.
Remove the four screws from the back panel (1), as shown:
Figure 4-23
Removing the power supply
7.
Slide the power supply toward the front
of the chassis and lift it out of the chassis (2).
Reinstalling or replacing the power supply
To install the power supply, reverse the steps completed for removal.
CAUTION:
To prevent possible equipment damage, see
Power connections
on page
73
to ensure
proper connection of power supply cables.
72
Chapter 4
Removal and replacement procedures
ENWW