HP Xw6600 HP xw6600 Workstation Service and Technical Reference Guide - Page 94

Installing a PCI Express card, PCI card, CAUTION,

Get HP Xw6600 - Workstation - 2 GB RAM PDF manuals and user guides
UPC - 883585731121
View all HP Xw6600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

CAUTION: To prevent possible heat damage to equipment if the workstation is powered up before replacing or reinstalling a removed PCI card, install a blank PCI slot cover in its place to maintain workstation chassis air flow integrity, then close the PCI retention clamp. If the PCI retention clamp levers do not readily close, verify that all cards are properly seated, and then try again. Remember to reinstall the workstation side access panel (see Side access panel on page 58). Installing a PCI Express card To install a PCI Express card: 1. Disconnect power from the system (see Predisassembly procedures on page 52). 2. Remove the side access panel (see Side access panel on page 58). 3. Open the PCI card retention clamp, press the retention clamp levers down to unsnap, and then rotate them up (1), as shown: Figure 4-38 Installing a PCI Express card 4. Remove the PCI slot cover (2). 5. Align the keyed components of the PCI card with the slot and then firmly seat the card in the slot (3). 6. Close the PCI card retention clamp by rotating the clamp downward and pressing the two green clamp levers from the rear panel of the chassis (4). 7. Reinstall PCI Express card support brackets if necessary, and reinstall the workstation side access panel. PCI card This section describes removing and installing PCI cards. 84 Chapter 4 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
CAUTION:
To prevent possible heat damage to equipment if the workstation is powered up
before replacing or reinstalling a removed PCI card, install a blank PCI slot cover in its place to
maintain workstation chassis air flow integrity, then close the PCI retention clamp.
If the PCI retention clamp levers do not readily close, verify that all cards are properly seated, and
then try again. Remember to reinstall the workstation side access panel (see
Side access panel
on page
58
).
Installing a PCI Express card
To install a PCI Express card:
1.
Disconnect power from the system (see
Predisassembly procedures
on page
52
).
2.
Remove the side access panel (see
Side access panel
on page
58
).
3.
Open the PCI card retention clamp, press the retention clamp levers down to unsnap, and then
rotate them up (1), as shown:
Figure 4-38
Installing a PCI Express card
4.
Remove the PCI slot cover (2).
5.
Align the keyed components of the PCI card with the slot and then firmly seat the card in the slot
(3).
6.
Close the PCI card retention clamp by rotating the clamp downward and pressing the two green
clamp levers from the rear panel of the chassis (4).
7.
Reinstall PCI Express card support brackets if necessary, and reinstall the workstation side access
panel.
PCI card
This section describes removing and installing PCI cards.
84
Chapter 4
Removal and replacement procedures
ENWW