Panasonic WJ-ND400K Operating Instructions - Page 191

Camera port/Client PC., 100M-Half / 10M-Full / 10M-Half

Get Panasonic WJ-ND400K PDF manuals and user guides View all Panasonic WJ-ND400K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 191 highlights

Network Network settings Item Settings Description NW link down detection Off♦ / On Specifies whether to detect disconnected network connection of Camera port/Client PC. Bandwidth control Unlimited♦ / 32Kbps / 64Kbps / 128Kbps / 256Kbps / 512Kbps / 1024Kbps / 2Mbps / 5Mbps / 10Mbps Specifies the maximum rate for data transmitted to the network. • The transmission amount is not limited in the case of an MPEG-4 live image. Port forwarding Specifies whether port forwarding is enabled. To configure this setting, click the [Setup >>] button. HTTP port number Port number input (80♦) Sets the HTTP port used when sending images in the range of 1 to 65535. Normally this setting is 80. • Depending on network settings, changing the HTTP port number may make communication impossible. If this happens, contact your network administrator. • Do not specify any of the following numbers for an FTP port number, site alarm port number, or port forwarding port number. 20, 21, 23, 25, 42, 53, 67, 68, 69, 79, 105, 110, 123, 161, 162, 546, 547, 995, 10001, 10002, 10003, 10004, 10005, 10006, 10007 FTP port number Port number input (21♦) Specifies the recorder FTP port number in the range of 1 to 65535. Normally this setting is 21. • Do not specify any of the following numbers for an HTTP port number, site alarm port number, or port forwarding port number. 20, 23, 25, 42, 53, 67, 68, 69, 79, 80, 105, 110, 123, 161, 162, 546, 547, 995, 10001, 10002, 10003, 10004, 10005, 10006, 10007 Network setup - Camera port/Client PC port DHCP Off♦ / On Specifies whether a DHCP server is used. • Select [On] to obtain the IP address, subnet mask, and default gateway from a DHCP server. Select [Off] to enter them manually. IP address Address input*1 When [DHCP] is [Off], specify the IP address here. Subnet mask Address input*1 When [DHCP] is [Off], specify the subnet mask here. Default gateway Address input*1 When [DHCP] is [Off], specify the default gateway here. Line speed Auto♦ / 1000M-Full / 100M-Full / Specifies the data line speed. 100M-Half / 10M-Full / 10M-Half Network setup - Maintenance port IP address Address input*1 Specifies the IP address. Subnet mask Address input*1 Specifies the subnet mask. DNS setup DNS Off♦ / Auto / Manual Specifies whether a DNS is used. • Selecting [Auto] enables auto detection of the DNS server. This setting is available only when [On] is selected for the [DHCP] setting of the Client PC port (page 61). • When [Manual] is selected, a primary address and secondary address can be specified for the DNS server IP address. Primary server address Address input (0.0.0.0♦) Enter the IP address of the primary DNS server. Secondary server address Address input (0.0.0.0♦) Enter the IP address of the secondary DNS server. Domain name Name input (local domain♦) Enter the domain name of the recorder. • Enter up to 255 single-byte alpha-numeric characters, including hyphen (-) and period (.). • Use an alphabetic character as the first character of the domain name. 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
Network
62
Network settings
Item
Settings
Description
NW link down detection
Off
♦
/ On
Specifies whether to detect disconnected network connection of
Camera port/Client PC.
Bandwidth control
Unlimited
♦
/ 32Kbps / 64Kbps /
12
8
Kbps / 256Kbps / 512Kbps /
1024Kbps / 2Mbps / 5Mbps /
10Mbps
Specifies the maximum rate for data transmitted to the network.
•
The transmission amount is not limited in the case of an
MPEG-4 live image.
Port forwarding
Specifies whether port forwarding is enabled. To configure this
setting, click the [Setup >>] button.
HTTP port number
Port number input
(
8
0
♦
)
Sets the HTTP port used when sending images in the range of
1 to 65535. Normally this setting is
8
0.
•
Depending on network settings, changing the HTTP port
number may make communication impossible. If this
happens, contact your network administrator.
•
Do not specify any of the following numbers for an FTP port
number, site alarm port number, or port forwarding port
number.
20, 21, 23, 25, 42, 53, 67, 6
8
, 69, 79, 105, 110, 123, 161,
162, 546, 547, 995, 10001, 10002, 10003, 10004, 10005,
10006, 10007
FTP port number
Port number input
(21
♦
)
Specifies the recorder FTP port number in the range of 1 to
65535. Normally this setting is 21.
•
Do not specify any of the following numbers for an HTTP
port number, site alarm port number, or port forwarding port
number.
20, 23, 25, 42, 53, 67, 6
8
, 69, 79,
8
0, 105, 110, 123, 161,
162, 546, 547, 995, 10001, 10002, 10003, 10004, 10005,
10006, 10007
Network setup - Camera port/Client PC port
DHCP
Off
♦
/ On
Specifies whether a DHCP server is used.
•
Select [On] to obtain the IP address, subnet mask, and
default gateway from a DHCP server. Select [Off] to enter
them manually.
IP address
Address input
*1
When [DHCP] is [Off], specify the IP address here.
Subnet mask
Address input
*1
When [DHCP] is [Off], specify the subnet mask here.
Default gateway
Address input
*1
When [DHCP] is [Off], specify the default gateway here.
Line speed
Auto
♦
/ 1000M-Full / 100M-Full /
100M-Half / 10M-Full / 10M-Half
Specifies the data line speed.
Network setup - Maintenance port
IP address
Address input
*1
Specifies the IP address.
Subnet mask
Address input
*1
Specifies the subnet mask.
DNS setup
DNS
Off
♦
/ Auto / Manual
Specifies whether a DNS is used.
•
Selecting [Auto] enables auto detection of the DNS server.
This setting is available only when [On] is selected for the
[DHCP] setting of the Client PC port (page 61).
•
When [Manual] is selected, a primary address and
secondary address can be specified for the DNS server IP
address.
Primary server address
Address input (0.0.0.0
♦
)
Enter the IP address of the primary DNS server.
Secondary server address
Address input (0.0.0.0
♦
)
Enter the IP address of the secondary DNS server.
Domain name
Name input (local domain
♦
)
Enter the domain name of the recorder.
•
Enter up to 255 single-byte alpha-numeric characters,
including hyphen (-) and period (.).
•
Use an alphabetic character as the first character of the
domain name.