HP Visualize J5000 hp Visualize J5000, J7000 workstations service handbook (a4 - Page 125

Removing an I/O Card, I/O Board

Get HP Visualize J5000 - Workstation PDF manuals and user guides View all HP Visualize J5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 125 highlights

Field Replaceable Units (FRUs) FRU Removal and Replacement I/O Cards The J5000 and J7000 workstations have 64-bit slots for PCI (Peripheral Connect Interface) I/O cards. As you face the front of the workstation, the I/O slots are located on the I/O board on the right side of the workstation. There are five PCI-2X slots, two PCI-4X slots, and one slot for power only. Removing an I/O Card To remove an I/O card, do the following: 1. Remove the top panel and the right side panel of the workstation. 2. Locate the I/O board and its I/O slots on the right side of the workstation, as shown in Figure 4-34. Note that the I/O board extends up behind the power supply, and that the eight I/O slots are located below the power supply. Figure 4-34. I/O Board PCI retainer clip Power supply I/O board (extends up behind the power supply, above) 3. Remove the PCI retainer clip by pressing down on the thumb tab and pulling the clip forward to rotate it out of the chassis floor hole, as shown in Figure 4-35 on the next page. Chapter 4 121

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
Chapter 4
121
Field Replaceable Units (FRUs)
FRU Removal and Replacement
I/O Cards
The J5000 and J7000 workstations have 64-bit slots for PCI (Peripheral Connect Interface)
I/O cards. As you face the front of the workstation, the I/O slots are located on the I/O
board on the right side of the workstation. There are five PCI-2X slots, two PCI-4X slots,
and one slot for power only.
Removing an I/O Card
To remove an I/O card, do the following:
1.
Remove the top panel and the right side panel of the workstation.
2.
Locate the I/O board and its I/O slots on the right side of the workstation, as shown in
Figure 4-34. Note that the I/O board extends up behind the power supply, and that the
eight I/O slots are located below the power supply.
Figure 4-34. I/O Board
3.
Remove the PCI retainer clip by pressing down on the thumb tab and pulling the clip
forward to rotate it out of the chassis floor hole, as shown in Figure 4-35 on the next
page.
I/O board (extends
up behind the power
supply, above)
Power supply
PCI retainer clip