HP Visualize J5000 hp Visualize J5000, J7000 workstations service handbook (a4 - Page 146

Speaker, Removing the Speaker, Removing the PCI Retainer Clip

Get HP Visualize J5000 - Workstation PDF manuals and user guides View all HP Visualize J5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 146 highlights

Field Replaceable Units (FRUs) FRU Removal and Replacement Speaker This section describes how to remove and replace the speaker, which is located in the fan/speaker mounting bracket in the bottom of the front, right side of the workstation. Removing the Speaker To remove the speaker, do the following: 1. Remove the top panel and the right side panel. 2. Remove the PCI retainer clip by pressing down on the thumb tab and pulling the clip forward to rotate it out of the chassis floor hole, as shown in Figure 4-60. Figure 4-60. Removing the PCI Retainer Clip 3. Remove all I/O cards from the I/O board and note their locations for reinstallation later. See the removal procedures in the section "I/O Cards" on page 121 for details. 4. Remove the power supply by following the removal procedures in "Power Supply" on page 128. 5. Disconnect the fan and speaker cables from the I/O board, as shown in Figure 4-61. Figure 4-61. Fan and Speaker Cables Connected to the I/O Board Fan/speaker mounting bracket Fan cable Speaker cable 142 Chapter 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
142
Chapter 4
Field Replaceable Units (FRUs)
FRU Removal and Replacement
Speaker
This section describes how to remove and replace the speaker, which is located in the
fan/speaker mounting bracket in the bottom of the front, right side of the workstation.
Removing the Speaker
To remove the speaker, do the following:
1.
Remove the top panel and the right side panel.
2.
Remove the PCI retainer clip by pressing down on the thumb tab and pulling the clip
forward to rotate it out of the chassis floor hole, as shown in Figure 4-60.
Figure 4-60. Removing the PCI Retainer Clip
3.
Remove all I/O cards from the I/O board and note their locations for reinstallation later.
See the removal procedures in the section “I/O Cards” on page 121 for details.
4.
Remove the power supply by following the removal procedures in “Power Supply” on
page 128.
5.
Disconnect the fan and speaker cables from the I/O board, as shown in Figure 4-61.
Figure 4-61. Fan and Speaker Cables Connected to the I/O Board
Fan cable
Speaker cable
Fan/speaker
mounting bracket