ASRock Z87 Extreme11/ac LSI Mega RAID Storage Manager Guide - Page 19

Installing a SNMP Agent on Windows

Get ASRock Z87 Extreme11/ac PDF manuals and user guides View all ASRock Z87 Extreme11/ac manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

# svcadm enable svc:/application/management/sma:default Note: Refer to the command man snmpd.conf for more information about configuring the snmpd.conf file. Configuring SNMP Traps To receive SNMP traps, perform the following steps: 1. Stop the LSI SAS SNMP Agent by using the following command: #/etc/init.d/lsi_mrdsnmpd stop 2. Edit the /etc/lsi_mrdsnmp/sas/sas_TrapDestination.conf file and add the IP address as shown in the following excerpt: Agent Service needs the IP addresses to sent trap # The trap destination may be specified in this file # or using snmpd.conf file. Following indicators can # be set on "TrapDestInd" to instruct the agent to # pick the IPs as the destination. # 1 - IPs only from snmpd.conf # 2 - IPs from this file only # 3 - IPs from both the files TrapDestInd 2 Trap Destination IP 127.0.0.1 public 172.28.157.149 public 3. Start the LSI SAS SNMP Agent by entering the following command: #/etc/init.d/lsi_mrdsnmpd start Uninstalling the SNMP Package The uninstall.sh script is located under the /etc/lsi_mrdsnmp/sas directory. Use the following command to uninstall the package: # cd /etc/lsi_mrdsnmp/sas # ./uninstall.sh Installing a SNMP Agent on Windows This section explains how to install and configure the SAS SNMP Agent for the Windows operating system. Installing SNMP Agent Perform the following steps to install the SNMP Agent: 1. Run setup.exe from DISK1. 2. Use the SNMP Manager to retrieve the SAS data (it is assumed that you have compiled LSI- AdapterSAS.mib file already). DB09-000202-05 37857-02 Installation Rev. F - May 2011 Copyright © 2011 by LSI Corporation. All rights reserved. Page 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
Installation
Page 19
DB09-000202-05 37857-02
Rev. F - May 2011
Copyright © 2011 by LSI Corporation. All rights reserved.
# svcadm enable svc:/application/management/sma:default
Note:
Refer to the command
man snmpd.conf
for more information about configuring the
snmpd.conf
file.
Configuring SNMP Traps
To receive SNMP traps, perform the following steps:
1.
Stop the LSI SAS SNMP Agent by using the following command:
#/etc/init.d/lsi_mrdsnmpd stop
2.
Edit the
/etc/lsi_mrdsnmp/sas/sas_TrapDestination.conf
file and add the IP address as
shown in the following excerpt:
#################################################
# Agent Service needs the IP addresses to sent trap
# The trap destination may be specified in this file # or using snmpd.conf
file. Following indicators can # be set on "TrapDestInd" to instruct the
agent to
# pick the IPs as the destination.
# 1 - IPs only from snmpd.conf
# 2 - IPs from this file only
# 3 - IPs from both the files
#################################################
TrapDestInd 2
#############Trap Destination IP##################
127.0.0.1
public
172.28.157.149 public
#################################################
3.
Start the LSI SAS SNMP Agent by entering the following command:
#/etc/init.d/lsi_mrdsnmpd start
Uninstalling the SNMP Package
The
uninstall.sh
script is located under the
/etc/lsi_mrdsnmp/sas
directory. Use the following
command to uninstall the package:
# cd /etc/lsi_mrdsnmp/sas
# ./uninstall.sh
Installing a SNMP Agent on Windows
This section explains how to install and configure the SAS SNMP Agent for the Windows operating
system.
Installing SNMP Agent
Perform the following steps to install the SNMP Agent:
1.
Run
setup.exe
from DISK1.
2.
Use the SNMP Manager to retrieve the SAS data (it is assumed that you have compiled
LSI-
AdapterSAS.mib
file already).