ASRock Z87 Extreme11/ac LSI Mega RAID Storage Manager Guide - Page 86

Setting Learn Cycle Properties

Get ASRock Z87 Extreme11/ac PDF manuals and user guides View all ASRock Z87 Extreme11/ac manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

To choose automatic battery learn cycles, enable automatic learn cycles. To choose manual battery learn cycles, disable automatic learn cycles. If you enable automatic learn cycles, you can delay the start of the learn cycles for up to 168 hours (7 days). If you disable automatic learn cycles, you can start the learn cycles manually, and you can choose to receive a reminder to start a manual learn cycle. Setting Learn Cycle Properties To set the learn cycle properties, perform the following steps: 1. Click the Physical tab to open the Physical view. 2. Select the BBU icon in the left panel. 3. Select Go To->BBU->Set Learn Cycle Properties. The Set Learn Cycle Properties window appears, as shown in the following figure. Figure 68 Set Learn Cycle Properties 4. Select one of the two automatic learn cycles: • Select the Enable radio button to enable an automatic learn cycle. • Select the Disable radio button to disable an automatic learn cycle. 5. You can delay the start of the next learn cycle up to 7 days (168 hours) by specifying the hours in the Delay scheduled learn cycle by field. 6. Select the Remind me when to start a learn cycle check box to receive a reminder to start a manual learn cycle. Note: After selecting Disable, if you select Enable, the controller firmware resets the battery module properties to initiate an immediate battery learn cycle. The Next Learn cycle field (in Figure 66 or Figure 67) will not be updated until the battery relearn is completed. Once the relearning cycle is completed, the value in the Next Learn cycle field will display the new date and the time of the next battery learning cycle. Page 86 DB09-000202-05 37857-02 Monitoring Controllers and Its Attached Devices Rev. F - May 2011 Copyright © 2011 by LSI Corporation. All rights reserved.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
Page 86
Monitoring Controllers and Its Attached Devices
DB09-000202-05 37857-02
Rev. F - May 2011
Copyright © 2011 by LSI Corporation. All rights reserved.
To choose automatic battery learn cycles, enable automatic learn cycles. To choose manual
battery learn cycles, disable automatic learn cycles.
If you enable automatic learn cycles, you can delay the start of the learn cycles for up to 168
hours (7 days). If you disable automatic learn cycles, you can start the learn cycles manually, and
you can choose to receive a reminder to start a manual learn cycle.
Setting Learn Cycle Properties
To set the learn cycle properties, perform the following steps:
1.
Click the
Physical
tab to open the Physical view.
2.
Select the
BBU
icon in the left panel.
3.
Select
Go To->BBU->Set Learn Cycle Properties
. The Set Learn Cycle Properties window
appears, as shown in the following figure.
Figure 68
Set Learn Cycle Properties
4.
Select one of the two automatic learn cycles:
•
Select the
Enable
radio button to enable an automatic learn cycle.
•
Select the
Disable
radio button to disable an automatic learn cycle.
5.
You can delay the start of the next learn cycle up to 7 days (168 hours) by specifying the
hours in the
Delay scheduled learn cycle by
field.
6.
Select the
Remind me when to start a learn cycle
check box
to receive a reminder to start
a manual learn cycle.
Note
:
After selecting
Disable
, if you select
Enable
, the controller firmware resets the
battery module properties to initiate an immediate battery learn cycle. The
Next
Learn cycle
field (in
Figure 66
or
Figure 67
) will not be updated until the battery
relearn is completed. Once the relearning cycle is completed, the value in the
Next
Learn cycle
field will display the new date and the time of the next battery learning
cycle.