Yamaha LS9-32 Owner's Manual - Page 21
SELECTED CHANNEL HA GAIN] encoder, PAN] encoder, SELECTED SEND] encoder, DYNAMICS 1] encoder - phantom power
View all Yamaha LS9-32 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 21 highlights
Top panel ⁄0 SELECTED CHANNEL section In this section you can operate the most important mix parameters for the currently selected input channel or output channel. The function of the controllers in this section will depend on the type of channel that is selected. 1 4 2 3 5 6 9 J 7 K 8 M L 1 [HA GAIN] encoder ● When an INPUT/ST IN channel is selected The encoder will adjust the gain of the internal head amp or an external head amp device (AD8HR) connected to a rear panel slot. NOTE • The PAD will be internally switched on or off when the HA gain is adjusted between -14 dB and -13 dB. Keep in mind that noise may be generated if there is a difference between the Hot and Cold output impedance of the external device connected to the INPUT connector when using phantom power. ● When any other channel is selected The encoder will not do anything. B [PAN] encoder ● When an INPUT/ST IN channel is selected ● When a MIX channel is selected The encoder will adjust the panning of the signal sent to the L/R channels (or the L/C/R channels in the case of LCR mode) of the STEREO bus. If a MIX channel set to stereo is selected, the encoder will adjust the output balance of the left and right channels. ● When a MATRIX channel is selected If a monaural MATRIX channel is selected, the encoder will not do anything. If a stereo MATRIX channel is selected, the encoder will adjust the output balance of the left and right channels. ● When a STEREO/MONO (C) channel is selected The encoder will not do anything for MONO (C) channel. For a STEREO channel, the encoder will adjust the output balance of the left and right channels. C [SELECTED SEND] encoder ● When an INPUT/ST IN channel is selected The encoder will adjust the send level from that chan- nel to the currently selected bus. (For a FIXED type bus, the encoder will switch the send on/off.) If the send-destination bus is stereo, this encoder will 2 specify the panning of the signal sent to the two buses if an odd-numbered bus is selected, or will specify the send level if an even-numbered bus is selected. Parts and their function ● When a MIX channel is selected The encoder will adjust the send level from that MIX channel to the currently selected MATRIX bus. ● When a MATRIX channel is selected The encoder will adjust the send level from the MIX channels to the currently selected MATRIX bus. NOTE • In SENDS ON FADER mode, this encoder will not do anything regardless of which channel is selected. D [DYNAMICS 1] encoder ● When an INPUT/ST IN channel is selected The encoder will adjust the threshold of Dynamics 1 (e.g., gate). ● When any other channel is selected The encoder will adjust the threshold of the compressor, etc. E [DYNAMICS 2] encoder ● When an INPUT/ST IN channel is selected The encoder will adjust the threshold of Dynamics 2 (e.g., compressor). ● When any other channel is selected The encoder will not do anything. F EQ [Q] encoder G EQ [FREQUENCY] encoder H EQ [GAIN] encoder These encoders adjust the Q, frequency, and gain of the band selected by keys 9-L. HINT • By simultaneously pressing the EQ [Q] encoder and the EQ [GAIN] encoder, you can reset the gain to 0 dB for the band selected by the keys below (9-L). • If you have selected a LOW band or HIGH band whose type can be changed, you can switch the type by turning the EQ [Q] encoder while pressing it when Q is set to the maximum or minimum value. LOW band : • Switches to LOW shelving if you turn the encoder toward the right while pressing it when Q is at the minimum value • Switches to high pass filter if you turn the encoder toward the left while pressing it when Q is at the maximum value (MIX, MATRIX, STEREO, and MONO channels only) HIGH band : • Switches to HIGH shelving if you turn the encoder toward the right while pressing it when Q is at the minimum value • Switches to low pass filter if you turn the encoder toward the left while pressing it when Q is at the maximum value For shelving, high pass filter, and low pass filter as well, you can switch the type by turning the encoder while pressing it. LS9-16/32 Owner's Manual 21