Yamaha LS9-32 Owner's Manual - Page 242
MULTI FILTER, FREEZE, STEREO REVERB, M. BAND DYNA., Two input, two output 3-band dynamics processor
View all Yamaha LS9-32 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 242 highlights
Effects Parameters ■ MULTI FILTER Two input, two output 3-band multi-filter (24 dB/octave). Parameter Range TYPE 1 LPF, HPF, BPF FREQ. 1 LEVEL 1 RESO. 1 28.0 Hz-16.0 kHz 0-100 0-20 TYPE 2 LPF, HPF, BPF FREQ. 2 LEVEL 2 RESO. 2 28.0 Hz-16.0 kHz 0-100 0-20 TYPE 3 LPF, HPF, BPF FREQ. 3 LEVEL 3 RESO. 3 28.0 Hz-16.0 kHz 0-100 0-20 Description Filter 1 type: high pass, low pass, band pass Filter 1 frequency Filter 1 level Filter 1 resonance Filter 2 type: high pass, low pass, band pass Filter 2 frequency Filter 2 level Filter 2 resonance Filter 3 type: high pass, low pass, band pass Filter 3 frequency Filter 3 level Filter 3 resonance ■ FREEZE One input, two output basic sampler. Parameter Range REC MODE MANUAL, INPUT REC DLY -1000 to +1000 ms PLY MODE MOMENT, CONTI., INPUT TRG LVL -60 to 0 dB TRG MASK 0-1000 ms START END LOOP LOOP NUM PITCH FINE *1 *1 *1 0-100 -12 to +12 semitones -50 to +50 cents MIDI TRG OFF, C1-C6, ALL START [SAMPLE] END [SAMPLE] LOOP [SAMPLE] 0-131000 0-131000 0-131000 Description In MANUAL mode, recording is started by pressing the REC and PLAY buttons. In INPUT mode, Record-Ready mode is engaged by pressing the REC button, and actual recording is triggered by the input signal. Recording delay. For plus values, recording starts after the trigger is received. For minus values, recording starts before the trigger is received. In MOMENT mode, the sample plays only while the that the PLAY button is pressed. In CONT mode, playback continues once the PLAY button has been pressed. The number of times the sample plays is set using the LOOP NUM parameter. In INPUT mode, playback is triggered by the input signal. Input trigger level (i.e., the signal level required to trigger recording or playback) Once playback has been triggered, subsequent triggers are ignored for the duration of the TRG MASK time. Playback start point in milliseconds Playback end point in milliseconds Loop start point in milliseconds Number of times the sample plays Playback pitch shift Playback pitch shift fine PLAY button can be triggered by using MIDI Note on/off messages. Playback start point in samples Playback end point in samples Loop start point in samples *1. 0.0-5941.0 ms (fs=44.1 kHz), 0.0 ms-5458.3 ms (fs=48 kHz) ■ STEREO REVERB Two input, two output stereo reverb. Parameter REV TIME REV TYPE INI. DLY HI. RATIO LO. RATIO DIFF. DENSITY E/R BAL. HPF LPF Range 0.3-99.0 s Hall, Room, Stage, Plate 0.0-100.0 ms 0.1-1.0 0.1-2.4 0-10 0-100% 0-100% THRU, 21.2 Hz- 8.00 kHz 50.0 Hz-16.0 kHz, THRU Description Reverb time Reverb type Initial delay before reverb begins High-frequency reverb time ratio Low-frequency reverb time ratio Reverb diffusion (left-right reverb spread) Reverb density Balance of early reflections and reverb (0% = all reverb, 100% = all early reflections) High-pass filter cutoff frequency Low-pass filter cutoff frequency ■ M. BAND DYNA. Two input, two output 3-band dynamics processor, with individual solo and gain reduction metering for each band. Parameter Range Description LOW GAIN -96.0 to +12.0 dB Low band level MID GAIN -96.0 to +12.0 dB Mid band level HI. GAIN -96.0 to +12.0 dB High band level PRESENCE -10 to +10 For positive values, the threshold of the high band is lowered and the threshold of the low band is increased. For negative values, the opposite will occur. When set to 0, all three bands are affected the same. L-M XOVR 21.2 Hz-8.00 kHz Low/mid crossover frequency M-H XOVR 21.2 Hz-8.00 kHz Mid/high crossover frequency SLOPE -6 dB, -12 dB Filter slope CEILING -6.0 dB to 0.0 dB, OFF Specifies the maximum output level CMP. THRE -24.0 dB to 0.0 dB Compressor threshold CMP. RAT 1:1 to 20:1 Compressor ratio CMP. ATK 0-120 ms Compressor attack CMP. REL *1 Compressor release time CMP. KNEE 0-5 Compressor knee CMP. BYP OFF/ON Compressor bypass LOOKUP 0.0-100.0 ms Lookup delay EXP. THRE -54.0 dB to -24.0 dB Expander threshold EXP. RAT 1:1 to ∞:1 Expander ratio EXP. REL *1 Expander release time EXP. BYP OFF/ON Expander bypass LIM. THRE -12.0 dB to 0.0 dB Limiter threshold LIM. ATK 0-120 ms Limiter attack LIM. REL *1 Limiter release time LIM. KNEE 0-5 Limiter knee LIM. BYP OFF/ON Limiter bypass *1. 6.0 ms-46.0 s (fs=44.1 kHz), 5.0 ms-42.3 s (fs=48 kHz) 242 LS9-16/32 Owner's Manual