Yamaha LS9-32 Owner's Manual - Page 65
Using the faders (SENDS ON FADER mode), TO MIX PAN/TO MIX BALANCE knob, Channel number / Channel name
View all Yamaha LS9-32 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 65 highlights
Sending the signal from an input channel to a MIX bus G TO MIX PAN/TO MIX BALANCE knob This knob adjusts the pan (or balance, for a ST IN channel) of the signal that is sent from the INPUT channel to the two MIX buses. HINT • If PRE is selected as the send position to the MIX bus, then you will also be able to select either PRE EQ (immediately before the attenuator) or PRE FADER (immediately before the fader) for each MIX bus (→ p. 213). • If desired, the pan/balance setting of the signal sent to a stereo MIX bus can be linked with the TO ST PAN/TO ST BAL knob of the SELECTED CH VIEW screen (→ p. 213). [ For a FIXED type MIX bus ] 1 2 8 To switch the on/off status of a signal sent to a VARI/FIXED type MIX bus, move the cursor to the TO MIX ON/OFF button in the screen and press the [ENTER] key. If the send-destination MIX bus is set to stereo, operation of the adjacent left/right pair of buttons is linked. 9 If you want to operate a channel that is not currently shown in the popup window, use the [SEL] key to select that channel, and then make settings for it. 10 If you want to adjust the send level to another MIX bus, use the keys of the MIX/ 5 MATRIX SELECT section to select another MIX bus, and make settings in the same way. 11 When you've finished making settings, move the cursor to the CLOSE button (or the × symbol in the upper right of the window) and press the [ENTER] key. Input channel operations 1 Channel number / Channel name This indicates the number and name of the sendsource channel. B TO MIX ON/OFF button This is an on/off switch for the signal that is sent from the send-source channel to the currently selected MIX bus. If the send-destination MIX bus is set to stereo, on/off operations are linked for adjacent odd-numbered/evennumbered MIX buses. 6 If you selected a VARI type MIX bus in step 4, move the cursor to the TO MIX LEVEL knob in the screen, and use the dial or the [DEC]/[INC] keys to adjust the send level from each channel to the selected MIX bus. If the send-destination MIX bus is set to stereo, move the cursor to the TO MIX PAN (TO MIX BALANCE) knob and adjust the pan (or balance, for a ST IN channel) of the signal sent from each channel to the two MIX buses. 7 To switch the send position of a signal sent to a VARI type MIX bus, move the cursor to the PRE button in the screen and press the [ENTER] key. If the PRE button is on, the pre-EQ or pre-fader signal will be sent; if this button is off, the signal from immediately after the [ON] key will be sent. HINT • If the PRE button is on, then you will be able to select either PRE EQ (immediately before the attenuator) or PRE FADER (immediately before the fader) for each MIX bus (→ p. 213). Using the faders (SENDS ON FADER mode) Here's how to use the top panel faders/encoders to adjust the send level and turn the signal on/off for the signals sent from all input channels to a specific MIX bus. 1 Make sure that an output port is assigned to the MIX bus to which you're sending the signal, and that a monitor system or external effect processor etc. is connected to the corresponding output port. 2 Press the SELECTED CHANNEL section [HOME] key. The SELECTED CH VIEW screen will appear in the display. 1 1 SEND popup button LS9-16/32 Owner's Manual 65