Yamaha LS9-32 Owner's Manual - Page 66
panel [ON] key., to a VARI/FIXED type MIX bus, press the top
View all Yamaha LS9-32 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 66 highlights
Sending the signal from an input channel to a MIX bus 3 Use the MIX/MATRIX SELECT section keys to select the send-destination MIX bus. The LED of the corresponding key will light, indicating that it is selected as the send-destination. 4 Press the same key of the MIX/MATRIX SELECT section once again. The key will change from lit to blinking, and the LEDs of the remaining keys in the MIX/MATRIX SELECT section will light. This indicates that the LS9 is now in SENDS ON FADER mode (in which you can use the faders to control the send levels to the MIX bus / MATRIX bus). In SENDS ON FADER mode, the function of the channel module section's faders and [ON] keys (the ST IN section's encoders and [ON] keys) will change as follows. ● Faders/Encoders These will adjust the send level of the signal sent from the input channels to the currently selected MIX bus. When you switch from normal mode to SENDS ON FADER mode, the fader positions will move to the value of the send levels to the currently selected MIX bus. ● [ON] keys These will operate as on/off switches for the signal sent from the input channels to the currently selected MIX bus. When you switch from normal mode to SENDS ON FADER mode, the [ON] keys will light or go dark according to the on/off status of the signals being sent to the currently selected MIX bus. ● [SEL] keys The [SEL] key of the selected channel will blink, and the [SEL] keys of channels that are not selected will light. However, the [SEL] keys of unassigned modules will go dark. 5 If you selected a VARI type MIX bus in step 3, use the faders of the channel module section and the encoders of the ST IN section to adjust the send level from the channels to the MIX bus you selected in step 3. As necessary, switch fader layers to the layer that contains the desired send-source input channels. 6 To switch the on/off status of a signal sent to a VARI/FIXED type MIX bus, press the top panel [ON] key. If the send-destination MIX bus is set to stereo, on/off operations will be linked for the signal sent to the two adjacent odd-numbered/even-numbered MIX buses. 7 Repeat steps 3-6 to adjust the send level and switch the on/off status for other MIX buses in the same way. 8 When you've finished setting the MIX send levels, press the key that is currently blinking in the MIX/MATRIX SELECT section. The LS9 will return to normal mode. HINT • You can assign the SENDS ON FADER function to a userdefined key. This allows you quickly switch to SENDS ON FADER mode for a specific MIX bus, or quickly return to the previous state. • You can also use the [HOME] key to cancel SENDS ON FADER mode. In SENDS ON FADER mode (when the send-destination is a MIX bus), the STEREO MASTER module will operate differently depending on the selected fader layer. Fader layer 1-16 {1-32}/17-32 {33-64} MASTER/CUSTOM FADER Function Send-destination MIX channel module STEREO channel (however, the fader and [ON] key will do nothing) NOTE • If you switch the fader layer from 1-16 {1-32}, 17-32 {33-64}, or CUSTOM FADER to MASTER while in SENDS ON FADER mode (when the send-destination is a MIX bus), SENDS ON FADER mode will be cancelled. • You cannot operate the fader or [ON] key of a channel that is not a send-source (a channel that does not have a MIX SEND parameter) or of a channel that is not a send-destination bus master. 66 LS9-16/32 Owner's Manual