Yamaha LS9-32 Owner's Manual - Page 238
Dyna. Phaser, Rev+chorus, Chorus, Rev+flange, One Input
View all Yamaha LS9-32 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 238 highlights
Effects Parameters ■ DYNA. PHASER Two input, two output dynamically controlled phaser. Parameter Range SOURCE INPUT, MIDI SENSE 0-100 DIR. UP, DOWN DECAY *1 OFFSET 0-100 FB.GAIN -99 to +99% STAGE LSH F LSH G HSH F HSH G 2, 4, 6, 8, 10, 12, 14, 16 21.2 Hz-8.00 kHz -12.0 to +12.0 dB 50.0 Hz-16.0 kHz -12.0 to +12.0 dB Description Control source: input signal or MIDI Note On velocity Sensitivity Upward or downward frequency change Decay speed Lowest phase-shifted frequency offset Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) Number of phase shift stages Low shelving filter frequency Low shelving filter gain High shelving filter frequency High shelving filter gain *1. 6.0 ms-46.0 s (fs=44.1 kHz), 5.0 ms-42.3 s (fs=48 kHz) ■ REV+CHORUS One input, two output reverb and chorus effects in parallel. Parameter REV TIME INI. DLY HI. RATIO DIFF. DENSITY Range 0.3-99.0 s 0.0-500.0 ms 0.1-1.0 0-10 0-100% REV/CHO 0-100% HPF THRU, 21.2 Hz- 8.00 kHz LPF 50.0 Hz-16.0 kHz, THRU FREQ. 0.05-40.00 Hz AM DEPTH 0-100% PM DEPTH 0-100% MOD. DLY 0.0-500.0 ms WAVE Sine, Tri SYNC OFF/ON NOTE *1 Description Reverb time Initial delay before reverb begins High-frequency reverb time ratio Spread Reverb density Reverb and chorus balance (0% = all reverb, 100% = all chorus) High-pass filter cutoff frequency Low-pass filter cutoff frequency Modulation speed Amplitude modulation depth Pitch modulation depth Modulation delay time Modulation waveform Tempo parameter sync on/off Used in conjunction with TEMPO to determine FREQ. *1. ■ REV→CHORUS One input, two output reverb and chorus effects in series. Parameter REV TIME INI. DLY HI. RATIO DIFF. DENSITY Range 0.3-99.0 s 0.0-500.0 ms 0.1-1.0 0-10 0-100% REV.BAL 0-100% HPF THRU, 21.2 Hz- 8.00 kHz LPF 50.0 Hz-16.0 kHz, THRU FREQ. 0.05-40.00 Hz AM DEPTH 0-100% PM DEPTH 0-100% MOD. DLY 0.0-500.0 ms WAVE Sine, Tri SYNC OFF/ON NOTE *1 Description Reverb time Initial delay before reverb begins High-frequency reverb time ratio Spread Reverb density Reverb and chorused reverb balance (0% = all chorused reverb, 100% = all reverb) High-pass filter cutoff frequency Low-pass filter cutoff frequency Modulation speed Amplitude modulation depth Pitch modulation depth Modulation delay time Modulation waveform Tempo parameter sync on/off Used in conjunction with TEMPO to determine FREQ. *1. ■ REV+FLANGE One input, two output reverb and flanger effects in parallel. Parameter REV TIME INI. DLY HI. RATIO DIFF. DENSITY REV/FLG HPF LPF FREQ. DEPTH MOD. DLY FB. GAIN WAVE SYNC NOTE Range 0.3-99.0 s 0.0-500.0 ms 0.1-1.0 0-10 0-100% 0-100% THRU, 21.2 Hz- 8.00 kHz 50.0 Hz-16.0 kHz, THRU 0.05-40.00 Hz 0-100% 0.0-500.0 ms -99 to +99% Sine, Tri OFF/ON *1 Description Reverb time Initial delay before reverb begins High-frequency reverb time ratio Spread Reverb density Reverb and flange balance (0% = all reverb, 100% = all flange) High-pass filter cutoff frequency Low-pass filter cutoff frequency Modulation speed Modulation depth Modulation delay time Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) Modulation waveform Tempo parameter sync on/off Used in conjunction with TEMPO to determine FREQ. *1. 238 LS9-16/32 Owner's Manual