Yamaha LS9-32 Owner's Manual - Page 98

vious screen., Make settings for delay, phase,

Page 98 highlights

Changing the output patching F Delay time setting knob This knob sets the delay time of the output port. Move the cursor to this knob and use the dial or the [DEC]/ [INC] keys to adjust the setting. The delay time value is shown below the knob, using the units selected in the DELAY SCALE field (3). G DELAY button Switches the delay on/off for the output port. H ø (phase) button Switches the phase of the signal assigned to the output port between normal phase (black) and reverse phase (orange). I ATT knob Adjusts the amount of attenuation/boost for the signal assigned to the output port. To change the setting, move the cursor to this knob in the screen, and use the dial or the [DEC]/[INC] keys. You can adjust the value in 1.0 dB steps in a range of -96 - +24 dB. The current value is shown immediately below the knob. J Level meter This meter shows the signal level of the channel assigned to the output port. 3 To assign a channel to an output port, move the cursor to the channel number field of that port, and press the [ENTER] key. The OUTPUT CH SELECT popup window will appear. This popup window contains the following items. 1 2 4 Use the category tabs and the channel select buttons to select the send-source channel. 5 Move the cursor to the CLOSE button and press the [ENTER] key to return to the previous screen. If PATCH is turned on in the CONFIRMATION field of the PREFERENCE popup window, a confirmation dialog box will appear when you attempt to modify the patching. If STEAL PATCH is turned on, a confirmation dialog box will appear if you attempt to change a location that is already patched to another location. (For details, refer to → p. 194) HINT • If you assign CH 1-32 {1-32/33-64} to an output port, the selected INPUT channel will be output directly from the corresponding output port. In this case, the channel select button in the OUTPUT PORT popup window will indicate "DIR CH xx" (xx = channel number). (For details on direct output → p. 103) 6 Make settings for delay, phase, and attenuator as necessary. 7 Repeat steps 3-6 to assign channels to other output ports. 8 When you've finished making settings, move the cursor to the CLOSE button (or to the × symbol in the upper right of the window), and press the [ENTER] key to return to the previous screen. LS9-32 1 Category tab This selects the type of channel that will be shown in the lower part of the window. Each tab corresponds to the following channels. ● OUT CH Output channels (MIX channels 1-16, MATRIX channels 1-8, STEREO L/R channel, and MONO (C) channel) will be shown. ● MONITOR OUT The MONITOR OUT L/R/C channels will be shown. ● CH 1-32 {1-32/33-64} INPUT channels 1-32 {1-64} will be shown. B Channel select button This selects the channel that is assigned to the output port. 98 LS9-16/32 Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290

98
Changing the output patching
LS9-16/32
Owner’s Manual
F
Delay time setting knob
This knob sets the delay time of the output port. Move
the cursor to this knob and use the dial or the [DEC]/
[INC] keys to adjust the setting. The delay time value
is shown below the knob, using the units selected in
the DELAY SCALE field (
3
).
G
DELAY button
Switches the delay on/off for the output port.
H
ø
(phase) button
Switches the phase of the signal assigned to the output
port between normal phase (black) and reverse phase
(orange).
I
ATT knob
Adjusts the amount of attenuation/boost for the signal
assigned to the output port. To change the setting,
move the cursor to this knob in the screen, and use the
dial or the [DEC]/[INC] keys. You can adjust the value
in 1.0 dB steps in a range of -96 – +24 dB. The current
value is shown immediately below the knob.
J
Level meter
This meter shows the signal level of the channel
assigned to the output port.
3
To assign a channel to an output port, move
the cursor to the channel number field of
that port, and press the [ENTER] key.
The OUTPUT CH SELECT popup window will
appear. This popup window contains the following
items.
1
Category tab
This selects the type of channel that will be shown in
the lower part of the window. Each tab corresponds to
the following channels.
OUT CH
Output channels (MIX channels 1–16, MATRIX
channels 1–8, STEREO L/R channel, and MONO
(C) channel) will be shown.
MONITOR OUT
The MONITOR OUT L/R/C channels will be
shown.
CH 1-32 {1-32/33-64}
INPUT channels 1–32 {1–64} will be shown.
B
Channel select button
This selects the channel that is assigned to the output
port.
4
Use the category tabs and the channel
select buttons to select the send-source
channel.
5
Move the cursor to the CLOSE button and
press the [ENTER] key to return to the pre-
vious screen.
If PATCH is turned on in the CONFIRMATION field
of the PREFERENCE popup window, a confirmation
dialog box will appear when you attempt to modify the
patching.
If STEAL PATCH is turned on, a confirmation dialog
box will appear if you attempt to change a location
that is already patched to another location. (For
details, refer to
p. 194)
6
Make settings for delay, phase, and
attenuator as necessary.
7
Repeat steps 3–6 to assign channels to
other output ports.
8
When you’ve finished making settings,
move the cursor to the CLOSE button (or to
the
×
symbol in the upper right of the win-
dow), and press the [ENTER] key to return
to the previous screen.
1
2
LS9-32
If you assign CH 1-32 {1-32/33-64} to an output port, the
selected INPUT channel will be output directly from the corre-
sponding output port. In this case, the channel select button
in the OUTPUT PORT popup window will indicate “DIR CH
xx” (xx = channel number). (For details on direct output
p. 103)
HINT