Yamaha LS9-32 Owner's Manual - Page 72
Channel number / Channel name, MODE button, ST button, TO ST PAN/TO ST BALANCE knob, CSR knob
View all Yamaha LS9-32 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 72 highlights
Sending signals from MIX channels to the STEREO/MONO bus 5 If you want to switch the on/off status of the signal sent from the MIX channel to the STEREO/MONO bus, or switch it between ST/MONO mode and LCR mode, use either of the following methods to access the TO STEREO/MONO popup window. • Move the cursor to the PAN popup button located in the TO ST field of the SELECTED CH VIEW screen, and press the [ENTER] key. • Move the cursor to the TO ST PAN knob located in the TO ST field of the SELECTED CH VIEW screen, and press the [ENTER] key. In the TO STEREO/MONO popup window you can switch between ST/MONO mode and LCR mode in sets of eight MIX channels, and change the on/off status and pan/balance settings of the signals sent from those channels to the STEREO/MONO bus. This popup window shows the parameters for the eight channels that include the MIX channel you selected in step 3. 1 2 3 4 5 HINT • If you've turned on POPUP APPEARS WHEN PRESSING KNOBS in the PREFERENCE popup window (→ p. 194), you can also access the above popup window by pressing the SELECTED CHANNEL section [PAN] encoder. This popup window contains the following items. 1 Channel number / Channel name This indicates the number and name of the channel you're operating. B MODE button This button selects either ST/MONO mode or LCR mode to specify how the signal is sent to the STEREO bus and MONO bus. You can specify this mode individually for each MIX channel. The setting will alternate between the two modes each time you press the button. The currently selected mode is shown by the position of the indicator (the green ◆ symbol) located immediately above the button. C ST button D MONO button When the MODE button is set to ST/MONO mode, these buttons act as individual on/off switches for the signal sent from that MIX channel to the STEREO bus and MONO bus. E TO ST PAN/TO ST BALANCE knob For monaural MIX channels, this acts as the PAN knob that adjusts the left/right panning of the signal sent to the STEREO bus. For stereo MIX channels, this acts as the BALANCE knob that adjusts the volume of the left and right signals sent to the STEREO bus. Move the cursor to the knob and use the dial or the [DEC]/[INC] keys to adjust the setting. For channels whose MODE button is set to LCR mode, the following button and knob are shown instead of the ST button (3) and MONO button (4). 6 7 F LCR button This button is an on/off switch for all signals sent from that MIX channel to the STEREO bus and MONO bus. If you turn off the button, no signals will be sent from that output channel to the STEREO bus or MONO bus. G CSR knob This knob adjusts the proportion between the signal level sent from that MIX channel to the STEREO (L/ R) bus and the level sent to the MONO (C) bus, over a range of 0-100%. To adjust the setting, move the cursor to the knob, press the [ENTER] key, and use the dial or the [DEC]/[INC] keys. 6 Use the MODE button to select either ST/ MONO mode or LCR mode for each MIX channel. 7 The ST button and MONO button are on/off switches for the signal sent from the MIX channel to the STEREO bus and MONO bus. 8 If you want to use the STEREO bus, make sure that the [ON] key of the STEREO channel is turned on in the top panel STEREO MASTER section, and raise the fader of the STEREO channel to an appropriate position. 72 LS9-16/32 Owner's Manual