Yamaha QL5 Reference Manual - Page 216

Message Monitor Assignment is Restricted to Max. 8 Sources! No Access From Recorder! No Channel Selected. No Copy Item Selected. No Corresponding Help Items. No ID3 Tag exists. You can not edit. No Response from External HA. No Response from I/O DEVICE. Operating as the word clock master. Page Bookmarked. Parameter out of range! Password Changed. PlayBack Failed: Recorder is Busy! PLAYBACK OUT CUE: Turned Off. Please use Dante Controller. Please wait, Dante patch is proceeding now. Power Supply Fan has Malfunctioned! PREVIEW Mode : Cannot Use This Function. PREVIEW Mode : Disabled PREVIEW Mode : Enabled Processing Aborted. Recorder Busy: Operation Aborted! RECORDER: CODEC Error [0x%08X] ! RECORDER IN CUE: Turned Off. Re-Enter Password! REMOTE: Data Framing Error! REMOTE: Data Overrun! REMOTE: Rx Buffer Full! REMOTE: Tx Buffer Full! Removed from the Channel Link group. Meaning The Monitor Define function allows a maximum of eight sources to be selected, but you attempted to assign more than eight. In the RECORDER screen, it is not possible to move to a level higher than \YPE\SONGS\. A copy-source channel was not selected in the GLOBAL PASTE screen. In the GLOBAL PASTE screen, you attempted to paste without having selected an item to paste. The corresponding section was not found in the Help file. The music file cannot be edited because it has no ID3 tag. No response from an external AD8HR. The I/O devices not responding. The QL series is operating correctly as a word clock master. The current screen or popup has been bookmarked. Some data could not be loaded because of a parameter mismatch. The password has been changed. Audio file link playback is not possible because recording is in progress. CUE was canceled for PLAYBACK OUT because you switched from the RECORDER screen to another screen. DANTE PATCH settings from the console are not enabled. You attempted to edit in the DANTE PATCH screen at a time when patching was not possible. The cooling fan of the internal power supply has stopped. Please contact your Yamaha service center listed at the end of the Owner's Manual (separate document). The operation was ignored because this function cannot be used during Preview. Preview was disabled. Preview was enabled. Processing was interrupted. Operation of the button was canceled because time is required for recorder processing. A codec error occurred in the RECORDER screen. CUE was canceled for RECORDER IN because you switched from the RECORDER screen to another screen. When specifying the user password, the password was not entered a second time. An inappropriate signal has been input to the Remote connector. Too much data has been received at the Remote connector. Too much data has been transmitted from the Remote connector. The channel was removed from the link group. Warning/Error Messages Message Saving Aborted. Saving Finished. SCENE #xxx is Empty! SCENE #xxx is Protected! SCENE #xxx is Read Only! Scene Playback Link Canceled! SLOT x: Data Framing Error! SLOT x: Data Overrun! SLOT x: Rx Buffer Full! SLOT x: Tx Buffer Full! Some Song Files Are Unidentified. Song File Not Found! STAGEMIX: Data Framing Error! STAGEMIX: Data Overrun! STAGEMIX: Rx Buffer Full! STAGEMIX: Tx Buffer Full! Storage Full! Storage Not Found! Storage Not Ready! Sync Error! [xxx] Tap Operation Ignored. This Operation is Not Allowed. This page does not exist in this model. Too Large Files! Loading Failed. Too Many Bands Used! Cannot Compare. Too Many Bands Used! Cannot Paste to Flex15GEQ. Total Slot Power Capability Exceeded! Unassigned Encoder. Unit Fan has Malfunctioned Meaning Saving to the USB flash drive has been interrupted. Finished saving to USB flash drive. No data has been stored in the scene you attempted to recall, or the data has been damaged so that it cannot be recalled. You attempted to overwrite (store) a protected scene. You attempted to overwrite (store) a read-only scene. The audio playback link for the scene was canceled. Invalid signals are being input to the SLOT x input port. Too much data is being received at the SLOT x input port. Too much data is being transmitted from the SLOT x output port. Some songs were not identified. Songs that have not been specified might be used for DIRECT PLAY or SCENE PLAY BACK LINK. The file specified for SCENE LINK or DIRECT PLAY assigned to a USER DEFINED key does not exist. Invalid signals are being exchanged with StageMix. Too much data is being received at the StageMix input port. Too much data is being transmitted from the StageMix output port. The file could not be saved because there is insufficient space on the USB flash drive. The USB flash drive could not be recognized. Access is not possible because the USB flash drive is not ready. The QL series console is not synchronized to the [xxx] signal. Tap operation was ignored because the TAP TEMPO button is not displayed in the screen. This operation has been ignored because the current user does not have permission. You attempted to open a bookmark or window that does not exist in the QL series. Loading is not possible because the bitmap file is too large. The maximum supported file size is 307,256 Bytes. Or loading is not possible because the bitmap file is too large. The maximum supported file size is 1024 kilobytes. Copying 31BandGEQ and comparing it to Flex15GEQ has failed because more than 15 bands are included in the copy source. Copying and pasting 31BandGEQ to Flex15GEQ has failed because more than 15 bands are included in the copy source. Power consumption of the I/O cards installed in the slots has exceeded the rated value. Your operation has been ignored because there is no parameter that corresponds to the knob you operated. The fan of the R series has malfunctioned. 216 Reference Manual