Yamaha QL5 Reference Manual - Page 8
PAN/BALANCE field, INPUT DELAY field, HPF field input channels only, EQ parameter field
![]() |
View all Yamaha QL5 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
PAN/BALANCE field This field enables you to switch the on/off status of the signal sent from the selected channel to the STEREO/MONO bus, and adjust the pan and balance. The view and the function of the controllers in this field vary depending on the type of the selected channel. When an input channel or MIX channel is selected: 1 TO STEREO PAN knob Sets the pan position of a signal routed to the STEREO bus. 1 2 Press the knob to open the STEREO/MONO 8ch window. If the ST IN channel is selected, you can specify whether to view the PAN knob or the BALANCE knob in this window. For a MIX channel, the PAN knob will appear if the signal is mono, and the BALANCE knob will appear if the signal is stereo. 2 ST/MONO button Switches the on/off status of a signal sent from the channel to the STEREO/MONO bus. If an INPUT/MIX channel is set to LCR mode, the 2 LCR button appears in location 2. The LCR button is an overall on/off switch for the signals sent from the channel to the STEREO/MONO bus. When a MATRIX, STEREO, or MONO channel is selected: 1 BALANCE knob If the signal on the selected channel is stereo, the BALANCE knob will appear, enabling you to adjust the volume balance for the left and right channels. 1 If the channel signal is monaural, this knob cannot be used. Press the knob to open the TO STEREO 8ch window. INPUT DELAY field This field enables you to view the delay settings. 1 1 ON indicator Indicates the on/off status of the delay. 2 2 Delay time The delay value is displayed by milliseconds (ms) and also by currently-selected scale. If the scale uses units of ms, the value in the bottom row will not be displayed. Only the ms value appears in the middle row. Press this field to open the INPUT DELAY 8ch window. HPF field (input channels only) This field enables you to set the HPF. If an output channel is selected, a gray circle will appear in location 1, and 2 will not be displayed. 1 1 HPF knob Sets the HPF cutoff frequency. 2 ON button Switches the HPF on or off. SELECTED CHANNEL section 2 EQ parameter field This field displays the 4-band EQ parameter settings. Press each knob to open the HPF/EQ 1ch window. 1 Q knob Specifies the Q for each band. If the HIGH band filter type is set to LPF or H. SHELF (highshelving), or the LOW band filter type is set to L. SHELF (low-shelving), the Q knob will not be displayed. Only the filter type name will be displayed. NOTE • Fully rotating the HIGH band Q knob on the panel counter- clockwise while pressing and holding it down will set the filter type to LPF. Fully rotating the Q knob clockwise while pressing and holding it down will set the filter type to high-shelving. • Fully rotating the LOW band Q knob on the panel clockwise while pressing and holding it down will set the filter type to low- shelving. 1 23 • If an output channel has been selected, fully rotating the LOW band Q knob on the panel counter-clockwise while pressing and holding it down will set the filter type to HPF. • You can also switch the filter type in the HPF/EQ 1ch window. 2 FREQUENCY knob Sets the center frequency (or cutoff frequency) for each band. 3 GAIN knob Sets the amount of cut/boost for each band. NOTE • If the HIGH band filter type is set to LPF, you can switch LPF on or off using the HIGH band GAIN knob on the panel. • If the LOW band filter type is set to HPF, you can switch HPF on or off using the LOW band GAIN knob on the panel. 8 Reference Manual
![](/manual_guide/products/yamaha-ql5-reference-manual-f6aaad0/8.png)