Home » Compaq Manuals » Servers » Compaq ProLiant 1000 » Manual Viewer

Compaq ProLiant 1000 ProLiant Server Troubleshooting Guide - Page 186

in Hot-Plug PCI Slot X, System ROM

Get Compaq ProLiant 1000 PDF manuals and user guides

View all Compaq ProLiant 1000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 186 highlights

POST Error Messages Table C-2: Non-Numeric Error Messages or Beeps Only continued Error Code Audible Beeps Probable Source of Problem Action Power Fault Detected 2 short in Hot-Plug PCI Slot X PCI-X Hot Plug expansion slot was not powered up properly. Reboot the server. Processor in incorrect socket. - System Halted!. None Processor is installed in socket 2 only. Install processor in socket 1. Processor packages do not match.. 1 long, 1 short Installed processors are different types. Install processors of the same type. Please make sure that all processor packages are the same. - System Halted! REDUNDANT ROM ERROR: Backup ROM invalid. - run ROMPAQ to correct error condition. None System ROM and redundant ROM are both corrupt. Run ROMPaq Utility. REDUNDANT ROM ERROR: Bootblock invalid. - contact COMPAQ Representative. None ROM bootblock is corrupt. Contact authorized service provider. RESUME - F1 key None As indicated to continue. Press the F1 key. (Run System Configuration Utility - F10 key) None A configuration error occurred during POST. Press the F10 key to run server setup utility. Unsupported Processor Detected System Halted. 1 long, 1 short Processor not supported by current system ROM. Check documentation for supported processors. If supported, remove the processor and update system to latest ROM. continued C-6 HP Servers Troubleshooting Guide

Section	Page
HP Servers Troubleshooting Guide	1
Notice	2
Contents	3
About This Guide	11
Who Should Use This Guide	11
How to Use This Guide	12
Key Terms	12
Symbols in Text	13
Reader’s Comments	13
HP Resources	13
Chapter 1: Diagnosing the Problem	14
Developing a Troubleshooting Plan	15
Preparing to Troubleshoot the Server	16
Preparing the Server for Diagnosis	16
Using a Troubleshooting Methodology	16
Gathering Information	18
Preliminary Information	18
When the Server Does Not Start	19
When a ProLiant ML, ProLiant DL, TaskSmart, or Previously Released Server Does Not Start	19
When a ProLiant BL Server Does Not Start	22
When the Self-Tests Fail	25
When the Operating System Does Not Load	28
Locating Troubleshooting Information	31
Contacting HP	33
Contacting Technical Support or Authorized Reseller	33
Server Information You Need	34
Operating System Information You Need	35
Microsoft Operating Systems	36
Linux Operating Systems	37
Novell NetWare Operating Systems	38
Caldera and SCO Operating Systems	39
IBM OS/2 Operating Systems	40
Sun Solaris Operating Systems	41
Banyan VINES Operating Systems	42
SQL Server	42
Chapter 2: Hardware Problems	43
Important Safety Information	44
Symbols on Equipment	44
Rack Stability	46
Power Problems	47
Power Source	47
Power Supply	48
System Power Module	48
Uninterruptible Power Supply	49
System Short Circuit	50
Redundant Line Cord Switch	51
General Hardware Problems	52
Loose Connections	52
Cabling Order	52
New Hardware	53
General Devices	54
Third-Party Devices	54
Universal Serial Bus Devices	54
Testing the Device	54
Rack Environment	55
Internal System Problems	56
Processors	56
Processor Power Modules	58
PCI or PCI-X Hot Plug	59
Memory	59
Fans	62
General Fan Problems	62
Hot-Plug Fan Problems	63
Drive Problems	64
Diskette Drives	64
CD-ROM and DVD Drives	65
Hard Drives	66
General Hard Drives	66
SCSI Non-Hot-Plug Hard Drives	68
SCSI Hot-Plug Hard Drives	68
Predictive Failure Alert	72
Tape Drives	73
DLT Drives	73
DAT Drives	76
External Device Problems	77
Video	77
Audio	79
Printers	79
Mouse and Keyboard	80
Diagnostic Adapter	81
Integrated Management Display	82
Hot-Plug Management Module	82
Network and Modem Problems	83
Network Controllers	83
Modems	85
Chapter 3: Software Problems	89
Operating Systems	90
Operating System Problems	90
Operating System Updates	93
Restoring to a Backed-Up Version	93
When to Reconfigure or Reload Software	94
Application Software	96
Clustering Software	97
Remote ROM Flash Problems	97
Maintaining Current Drivers	100
Erasing the System	102
Chapter 4: Diagnostic Tools	104
Array Diagnostic Utility	105
Diagnostics	106
Enterprise Diagnostics LX32	106
Accessing Enterprise Diagnostics LX32	108
Running Tests	108
Saving Error Reports	108
Diagnostics on a 32-bit System	108
Running Diagnostics	109
Diagnostics on a 64-bit System	109
Running Diagnostics	109
Exiting Diagnostics	110
Server Management	111
Server Management on 64-bit Servers	111
Survey Utility	112
Running Survey Utility	112
Diagnostic Adapter	113
Diagnostic Station	113
Inspect Utility	113
Running Inspect on a 32-bit System	113
Running Inspect on a 64-bit System	114
Integrated Administrator	115
Integrated Lights-Out	115
Integrated Management Log	115
List of Events	116
Power-On Self-Test	121
BIOS Serial Console	121
Server Blade Health Driver	121
Chapter 5: Error Recovery	122
ROMPaq Disaster Recovery	123
Redundant ROM Image Recovery	125
Automatic Server Recovery-2	125
Unattended Recovery	126
Attended Recovery	127
Hardware Requirements	127
Health Driver	130
Initiating Diagnostics	131
Initiating the Operating System	135
ASR-2 Password Security	136
ASR-2 Integrated Management Log Messages	136
Automatic Revision Tracking	139
Storage Fault Recovery Tracking	140
Storage Automatic Reconstruction	140
Network Interface Fault Recovery Tracking	140
Memory Fault Recovery Tracking	140
Chapter 6: Error Prevention	141
Preparing for Changes	142
Minimizing the Impact of Changes by Using HP Too	143
Managing Updates Through Integration Servers	143
Installing Servers Consistently Through Replicate	144
Maintaining Server Software	144
Other Ways to Minimize the Impact of Changes	144
Version Control	144
Server Design	144
Minimizing Updates	145
Using a Methodology	145
Visually Checking Your Server	147
Recognizing Power Problems Caused by Acts of Nat	148
Preventing Power Management Problems	148
General Power Requirements	149
Power Consumption Considerations	149
Power Supply Considerations	149
Power Cord Considerations	149
Power Redundancy Considerations	150
Preventing Grounding Problems	150
Preventing Temperature Problems	150
Preventing Damage to Removable Drives	151
Preventing Electrostatic Damage	152
Preventing Cable Damage	152
Preventing Tape Drive Errors	153
Appendix A: HP Resources	154
Online Resources	155
Software and Option Resources	157
General Server Resources	162
ProLiant BL e-Class System Resources	165
Appendix B: Test Error Codes	166
100-199, Primary Processor Test Error Codes	167
200-299, Memory Test Error Codes	168
300-399, Keyboard Test Error Codes	170
400-499, Parallel Printer Test Error Codes	171
500599, Graphics Controller Unit Test Error Co	172
600-699, Diskette Drive Test Error Codes	173
1100-1199, Serial Test Error Codes	174
1200-1299, Modem Communications Test Error Code	175
6000-6099, Network Interface Controllers Test Er	176
6100-6199, Array Controller Test Error Codes	177
6500-6599, SCSI Hard Drive Test Error Codes	178
6600-6699, SCSI/IDE CD-ROM Drive Test Error Co	179
6700-6799, SCSI Tape Drive Test Error Codes	180
8600-8699, Pointing Device Interface Test Error Codes	180
Appendix C: POST Error Messages	181
Non-Numeric POST Error Messages or Beeps Only	182
100 Series POST Error Messages	187
200 Series POST Error Messages	194
300 Series POST Error Messages	205
400 Series POST Error Messages	207
500 Series POST Error Messages	207
600 Series POST Error Messages	208
800 Series POST Error Messages	210
900 Series POST Error Messages	216
1100 Series POST Error Messages	217
1600 Series POST Error Messages	218
1700 Series POST Error Messages	227
1800 Series POST Error Messages	250
Appendix D: ADU Error Messages	251

Match case Limit results 1 per page

POST Error Messages

C-6

HP Servers Troubleshooting Guide

Table C-2:

Non-Numeric Error Messages or Beeps Only

continued

Error Code

Audible

Beeps

Probable Source of

Problem

Action

Power Fault Detected

in Hot-Plug PCI Slot X

2 short

PCI-X Hot Plug

expansion slot was not

powered up properly.

Reboot the server.

Processor in incorrect

socket. - System

Halted!.

None

Processor is installed in

socket 2 only.

Install processor in socket 1.

Processor packages

do not match..

Please make sure

that all processor

packages are the

same.

- System Halted!

1 long,

1 short

Installed processors are

different types.

Install processors of the same

type.

REDUNDANT ROM

ERROR: Backup

ROM invalid. - run

ROMPAQ to correct

error condition.

None

System ROM and

redundant ROM are both

corrupt.

Run ROMPaq Utility.

REDUNDANT ROM

ERROR: Bootblock

invalid. - contact

COMPAQ

Representative.

None

ROM bootblock is

corrupt.

Contact authorized service

provider.

RESUME – F1 key

None

As indicated to continue.

Press the

key

(Run System

Configuration Utility –

F10 key)

None

A configuration error

occurred during POST.

Press the

F10

key to run

server setup utility.

Unsupported

Processor Detected

System Halted.

1 long, 1

short

Processor not supported

by current system ROM.

Check documentation for

supported processors. If

supported, remove the

processor and update system

to latest ROM.

continued