Home » Compaq Manuals » Servers » Compaq ProLiant 1000 » Manual Viewer

Compaq ProLiant 1000 ProLiant Server Troubleshooting Guide - Page 191

Comport Invalid, PCI Comport, Invalid, Incorrect IRQ, Video, Controller Must, be on Primary, PCI Bus

Get Compaq ProLiant 1000 PDF manuals and user guides

View all Compaq ProLiant 1000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 191 highlights

POST Error Messages Table C-3: 100 Series POST Error Messages continued Error Code Audible Beeps Probable Source of Problem 171-2-IRC Configuration Invalid None One or more of the following messages may also be displayed: • Comport Invalid • PCI Comport Invalid • Incorrect IRQ • Video Controller Must be on Primary PCI Bus 172-1-Configuration NVRAM invalid None Nonvolatile configuration corrupted or jumper installed. 172-Configuration Non-volatile Memory Invalid None Nonvolatile configuration corrupted. 172-Default System Configuration Installed! Run System Configuration Utility to View/Modify Settings None Nonvolatile configuration corrupted. The default system configuration has been installed. 172-1-Configuration Non-volatile Memory Invalid None Nonvolatile configuration corrupted. 172-System Configuration Nonvolatile Memory Invalid. Initialization Aborted. None Battery is low or not working. 173-PCI Config Slot Mismatch None Board replaced, configuration not updated. Action Run the server setup utility and correct. Run the server setup utility and correct. Run the server setup utility and correct. Run the server setup utility to make any changes to the default configuration. Run the server setup utility and correct. Turn off the server, replace the battery located on the sideplane board, and then reboot the system. The default nonvolatile configuration will be loaded. Run the server setup utility and correct. continued HP Servers Troubleshooting Guide C-11

Section	Page
HP Servers Troubleshooting Guide	1
Notice	2
Contents	3
About This Guide	11
Who Should Use This Guide	11
How to Use This Guide	12
Key Terms	12
Symbols in Text	13
Reader’s Comments	13
HP Resources	13
Chapter 1: Diagnosing the Problem	14
Developing a Troubleshooting Plan	15
Preparing to Troubleshoot the Server	16
Preparing the Server for Diagnosis	16
Using a Troubleshooting Methodology	16
Gathering Information	18
Preliminary Information	18
When the Server Does Not Start	19
When a ProLiant ML, ProLiant DL, TaskSmart, or Previously Released Server Does Not Start	19
When a ProLiant BL Server Does Not Start	22
When the Self-Tests Fail	25
When the Operating System Does Not Load	28
Locating Troubleshooting Information	31
Contacting HP	33
Contacting Technical Support or Authorized Reseller	33
Server Information You Need	34
Operating System Information You Need	35
Microsoft Operating Systems	36
Linux Operating Systems	37
Novell NetWare Operating Systems	38
Caldera and SCO Operating Systems	39
IBM OS/2 Operating Systems	40
Sun Solaris Operating Systems	41
Banyan VINES Operating Systems	42
SQL Server	42
Chapter 2: Hardware Problems	43
Important Safety Information	44
Symbols on Equipment	44
Rack Stability	46
Power Problems	47
Power Source	47
Power Supply	48
System Power Module	48
Uninterruptible Power Supply	49
System Short Circuit	50
Redundant Line Cord Switch	51
General Hardware Problems	52
Loose Connections	52
Cabling Order	52
New Hardware	53
General Devices	54
Third-Party Devices	54
Universal Serial Bus Devices	54
Testing the Device	54
Rack Environment	55
Internal System Problems	56
Processors	56
Processor Power Modules	58
PCI or PCI-X Hot Plug	59
Memory	59
Fans	62
General Fan Problems	62
Hot-Plug Fan Problems	63
Drive Problems	64
Diskette Drives	64
CD-ROM and DVD Drives	65
Hard Drives	66
General Hard Drives	66
SCSI Non-Hot-Plug Hard Drives	68
SCSI Hot-Plug Hard Drives	68
Predictive Failure Alert	72
Tape Drives	73
DLT Drives	73
DAT Drives	76
External Device Problems	77
Video	77
Audio	79
Printers	79
Mouse and Keyboard	80
Diagnostic Adapter	81
Integrated Management Display	82
Hot-Plug Management Module	82
Network and Modem Problems	83
Network Controllers	83
Modems	85
Chapter 3: Software Problems	89
Operating Systems	90
Operating System Problems	90
Operating System Updates	93
Restoring to a Backed-Up Version	93
When to Reconfigure or Reload Software	94
Application Software	96
Clustering Software	97
Remote ROM Flash Problems	97
Maintaining Current Drivers	100
Erasing the System	102
Chapter 4: Diagnostic Tools	104
Array Diagnostic Utility	105
Diagnostics	106
Enterprise Diagnostics LX32	106
Accessing Enterprise Diagnostics LX32	108
Running Tests	108
Saving Error Reports	108
Diagnostics on a 32-bit System	108
Running Diagnostics	109
Diagnostics on a 64-bit System	109
Running Diagnostics	109
Exiting Diagnostics	110
Server Management	111
Server Management on 64-bit Servers	111
Survey Utility	112
Running Survey Utility	112
Diagnostic Adapter	113
Diagnostic Station	113
Inspect Utility	113
Running Inspect on a 32-bit System	113
Running Inspect on a 64-bit System	114
Integrated Administrator	115
Integrated Lights-Out	115
Integrated Management Log	115
List of Events	116
Power-On Self-Test	121
BIOS Serial Console	121
Server Blade Health Driver	121
Chapter 5: Error Recovery	122
ROMPaq Disaster Recovery	123
Redundant ROM Image Recovery	125
Automatic Server Recovery-2	125
Unattended Recovery	126
Attended Recovery	127
Hardware Requirements	127
Health Driver	130
Initiating Diagnostics	131
Initiating the Operating System	135
ASR-2 Password Security	136
ASR-2 Integrated Management Log Messages	136
Automatic Revision Tracking	139
Storage Fault Recovery Tracking	140
Storage Automatic Reconstruction	140
Network Interface Fault Recovery Tracking	140
Memory Fault Recovery Tracking	140
Chapter 6: Error Prevention	141
Preparing for Changes	142
Minimizing the Impact of Changes by Using HP Too	143
Managing Updates Through Integration Servers	143
Installing Servers Consistently Through Replicate	144
Maintaining Server Software	144
Other Ways to Minimize the Impact of Changes	144
Version Control	144
Server Design	144
Minimizing Updates	145
Using a Methodology	145
Visually Checking Your Server	147
Recognizing Power Problems Caused by Acts of Nat	148
Preventing Power Management Problems	148
General Power Requirements	149
Power Consumption Considerations	149
Power Supply Considerations	149
Power Cord Considerations	149
Power Redundancy Considerations	150
Preventing Grounding Problems	150
Preventing Temperature Problems	150
Preventing Damage to Removable Drives	151
Preventing Electrostatic Damage	152
Preventing Cable Damage	152
Preventing Tape Drive Errors	153
Appendix A: HP Resources	154
Online Resources	155
Software and Option Resources	157
General Server Resources	162
ProLiant BL e-Class System Resources	165
Appendix B: Test Error Codes	166
100-199, Primary Processor Test Error Codes	167
200-299, Memory Test Error Codes	168
300-399, Keyboard Test Error Codes	170
400-499, Parallel Printer Test Error Codes	171
500599, Graphics Controller Unit Test Error Co	172
600-699, Diskette Drive Test Error Codes	173
1100-1199, Serial Test Error Codes	174
1200-1299, Modem Communications Test Error Code	175
6000-6099, Network Interface Controllers Test Er	176
6100-6199, Array Controller Test Error Codes	177
6500-6599, SCSI Hard Drive Test Error Codes	178
6600-6699, SCSI/IDE CD-ROM Drive Test Error Co	179
6700-6799, SCSI Tape Drive Test Error Codes	180
8600-8699, Pointing Device Interface Test Error Codes	180
Appendix C: POST Error Messages	181
Non-Numeric POST Error Messages or Beeps Only	182
100 Series POST Error Messages	187
200 Series POST Error Messages	194
300 Series POST Error Messages	205
400 Series POST Error Messages	207
500 Series POST Error Messages	207
600 Series POST Error Messages	208
800 Series POST Error Messages	210
900 Series POST Error Messages	216
1100 Series POST Error Messages	217
1600 Series POST Error Messages	218
1700 Series POST Error Messages	227
1800 Series POST Error Messages	250
Appendix D: ADU Error Messages	251

Match case Limit results 1 per page

POST Error Messages

HP Servers Troubleshooting Guide

C-11

Table C-3:

100 Series POST Error Messages

continued

Error Code

Audible

Beeps

Probable Source of

Problem

Action

171-2-IRC

Configuration Invalid

None

One or more of the

following messages may

also be displayed:

•

Comport Invalid

•

PCI Comport

Invalid

•

Incorrect IRQ

•

Video

Controller Must

be on Primary

PCI Bus

Run the server setup utility

and correct.

172-1-Configuration

NVRAM invalid

None

Nonvolatile configuration

corrupted or jumper

installed.

Run the server setup utility

and correct.

172-Configuration

Non-volatile Memory

Invalid

None

Nonvolatile configuration

corrupted.

Run the server setup utility

and correct.

172-Default System

Configuration

Installed! Run System

Configuration Utility to

View/Modify Settings

None

Nonvolatile configuration

corrupted. The default

system configuration has

been installed.

Run the server setup utility to

make any changes to the

default configuration.

172-1-Configuration

Non-volatile Memory

Invalid

None

Nonvolatile configuration

corrupted.

Run the server setup utility

and correct.

172-System

Configuration

Nonvolatile Memory

Invalid. Initialization

Aborted.

None

Battery is low or not

working.

Turn off the server, replace

the battery located on the

sideplane board, and then

reboot the system. The

default nonvolatile

configuration will be loaded.

173-PCI Config Slot

Mismatch

None

Board replaced,

configuration not

updated.

Run the server setup utility

and correct.

continued