Yamaha CS1D Owner's Manual - Page 289
DCA [MUTE] switch and LED, DCA [ASSIGN DCA] switch and LED, DCA fader, DCA [NOMINAL] LED
View all Yamaha CS1D manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 289 highlights
CS1D Reference Manual (Hardware) Hint If the bands of the internal graphic EQ are assigned to the DCA faders, the upper row of indicators will display the frequency of the corresponding band, and the lower row will display the gain value. 2 DCA [MUTE] switch and LED This switch mutes the corresponding DCA group 1- 12. When you press this switch, the DCA [MUTE] LED will light, and the input channels/output channels included in that DCA group will be set to the same status as if the DCA fader were set to the minimum level (- ∞ dB). When you press the switch once again, the DCA [MUTE] LED will go dark, and muting will be canceled. Hint The DCA [MUTE] switch and LED will have no effect if input channels or output channels are directly assigned to the DCA faders, or if the graphic EQ is assigned. Be careful not to confuse muting performed by the DCA [MUTE] switch with mute groups (performed in the MASTER block SCENE MEMORY section). The operation of the DCA [MUTE] switch is identical to the MUTE button in the IN DCA/MUTE function DCA ASSIGN screen and the OUT DCA/ MUTE function DCA ASSIGN screen. 3 DCA [ASSIGN DCA] switch and LED This switch selects the DCA group for which input channels or output channels (MIX channels) will be registered. 4 DCA fader This is a 100 mm fader that sets the level of the input channel, output channel, or DCA group selected by the FADER STATUS section. If the internal graphic EQ is assigned to the DCA faders, this sets the amount of boost/cut for the corresponding band. 5 DCA [NOMINAL] LED If input channels or output channels are directly assigned to the DCA faders, or if DCA groups are assigned, this LED will light when the fader is set to nominal level (0 dB). If the internal graphic EQ is assigned to the DCA faders, this LED will light when the gain value is 0 dB. 6 DCA SAFE [RECALL] LED If DCA groups 1-12 are assigned to the DCA faders, this LED will light to indicate DCA groups that are set to Recall Safe (a state in which the DCA group will be unaffected by scene recall operations). A DCA fader for which this LED is lit will not change even if a scene memory is recalled. If input channels / output channels are directly assigned to the DCA faders, this LED will light to indicate channels that are set to Recall Safe. A channel for which this LED is lit will not change even if a scene memory is recalled. Simply setting a DCA fader to Recall Safe means only that the corresponding DCA fader will be exempted from Recall operations, the various channels that belong to that DCA group are not affected by this. If necessary, you must also set the individual channels to Recall Safe. Recall safe settings can be made in the display (SCENE function RECALL SAFE screen). If the graphic EQ has been assigned to the DCA faders, this LED will have no function. 7 DCA [CUE] switch and LED This switch monitors the channel(s) assigned to the DCA fader. If this switch is pressed when a DCA group 1-12 is assigned to the DCA fader, all input channels (or output channels) assigned to that DCA group will be sent to the CUE bus, and can be monitored from the CUE OUT jacks, MONITOR OUT jacks A, or PHONES jack. If this switch is pressed when an input channel/output channel is directly assigned to the DCA fader, the signal of the corresponding channel will be sent to the CUE bus. (This will have the same function as the [CUE] switch provided for each channel.) The location and monitoring method for the signal sent to the CUE bus can be selected on the console in the MASTER block CUE section, or in the display (MON/CUE function CUE/SOLO screen). If the graphic EQ has been assigned to the DCA faders, this switch will have no function. 72