Yamaha CS1D Owner's Manual - Page 299
Any CUE group other than INPUT/DCA/OUT, DCA PRE PAN] switch and LED
View all Yamaha CS1D manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 299 highlights
CS1D Reference Manual (Hardware) When this switch is on (the LED will light), the signal will be sent from the PFL (pre-fader listen) position to the CUE bus. When this switch is off, the signal will be sent from the POST ON (immediately after the [ON] switch) position to the CUE bus. 5 CUE ACTIVE [INPUT]/[DCA]/[OUTPUT] LEDs These LEDs indicate the state of monitoring. If even one [CUE] switch is currently on, the LED corresponding to that monitor source will light. The monitor source corresponding to each LED is as follows. • INPUT This will light when a channel of the INPUT CUE group (input channel, ST IN channel) is being monitored. • DCA This will light when a channel of the DCA CUE group is being monitored. • OUTPUT This will light when a channel of the OUTPUT CUE group (MIX channel, MATRIX channel, STEREO A/ B channel) is being monitored. [INPUT]/[DCA]/[OUTPUT] all lit All three LEDs will light when one of the following buttons or switches of a CUE group other than INPUT/DCA/OUTPUT CUE is pressed. • EFFECT CUE button (EFFECT function) • GATE KEY IN CUE button (IN GATE/COMP function GATE PRM screen), or INPUT SELECTED CHANNEL [GATE KEY IN CUE] switch • SUB IN CUE button (MATRIX/ST function SUB IN screen) 6 [LAST CUE] switch and LED This switch specifies what will occur when you press the [CUE] switch of two or more channels. When the LED is lit, LAST CUE mode is selected. When the LED is dark, MIX CUE mode is selected. Operation will differ in the following ways. • LAST CUE mode Only the channel whose [CUE] switch was pressed last will be monitored. • MIX CUE mode All channels whose [CUE] switches are currently on will be mixed and monitored. MIX CUE mode is valid only when you press the [CUE] switches of input channels, output channels, or the DCA section. For example while the SELECTED INPUT CHANNEL block NOISE GATE KEY IN [CUE] switch is on, only the key-in signal of the noise gate built into that channel will be given priority for monitoring. Hint On the PM1D system, Cue can be classified into the following three groups. 1) INPUT CUE group (Gate key-in cue signals from input channels or ST IN channels) 2) DCA CUE group (cue signals from DCA groups) 3) OUTPUT CUE group (cue signals from MIX channels, MATRIX channels, or STEREO A/B channels) 4) Any CUE group other than INPUT/DCA/OUTPUT CUE (i.e., the EFFECT CUE button within the EFFECT function, the KEY IN CUE button within the GATE PRM screen or SELECTED INPUT CHANNEL of the IN GATE/COMP function, or the SUB IN CUE button in the SUB IN screen of the MATRIX/ST function) It is not possible for [CUE] switches or buttons of these four groups to be on simultaneously. The group for the last-pressed [CUE] switch or button will take priority, and the signals of that group can be monitored. If you switch groups in the order of "OUTPUT CUE →DCA CUE," "OUTPUT CUE → INPUT CUE," "DCA CUE → INPUT CUE," or "INPUT/OUTPUT/ DCA CUE → CUE other than INPUT/OUTPUT/ DCA," the state of the group or [CUE] switch or button before the change will be remembered, and if the currently-on [CUE] switches or buttons are all turned off, you will return to the previous group. When you press the [LAST CUE] switch to switch from LAST CUE mode to MIX CUE mode (or vice versa), the previously-effective cue (solo) will be cancelled. 7 [DCA PRE PAN] switch and LED This switch selects the location in the signal route at which the signal will be monitored when a [CUE] switch in the DCA GROUP block is used to monitor a DCA group to which input channels are assigned. If this switch is on, turning on the [CUE] switch of a DCA group to which input channels are assigned will allow monitoring of the signal immediately before pan. If this switch is off, the signal immediately after pan will be monitored. This switch is valid only for DCA groups to which input channels are assigned. If you use the [CUE] switch to monitor a DCA group to which output channels are assigned, the signal will always be sent from the POST ON location (after the [ON] switch) to the CUE bus. 82