Dell PowerEdge T605 Hardware Owner's Manual (PDF) - Page 37

Plug & Play, reset: Slot X - install disks

Get Dell PowerEdge T605 PDF manuals and user guides View all Dell PowerEdge T605 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Table 1-6. System Messages (continued) Message Causes Corrective Actions PCIe Fatal Error caused a system reset: Slot X Embedded Bus#XX/Dev#XX/Fu ncX PCI Express fatal errors Reseat the PCIe card in the occurred during the previous specified slot number (see boot. "Installing an Expansion Card" on page 110). If the problem persists, see "Getting Help" on page 205. Please check the system event log for details Plug & Play Configuration Error Error encountered in initializing PCIe device; faulty system board. Install the NVRAM_CLR jumper and restart the system. See Figure 6-1 for jumper location. If the problem persists, see "Troubleshooting Expansion Cards" on page 187. Read fault Requested sector not found The operating system cannot Replace the USB medium or read from the hard drive or device. Ensure that the USB USB device, the system could or hard drive cables are not find a particular sector on properly connected. See the disk, or the requested "Troubleshooting a USB sector is defective. Device" on page 165, or "Troubleshooting a Hard Drive" on page 181 for the appropriate drive(s) installed in your system. Remote configuration update attempt failed System unable to process Remote Configuration request. Retry Remote Configuration. About Your System 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
About Your System
37
PCIe Fatal Error
caused a system
reset: Slot X
Embedded
Bus#XX/Dev#XX/Fu
ncX
Please check the
system event log
for details
PCI Express fatal errors
occurred during the previous
boot.
Reseat the PCIe card in the
specified slot number (see
"Installing an Expansion
Card" on page 110). If the
problem persists, see
"Getting Help" on page 205.
Plug & Play
Configuration
Error
Error encountered in
initializing PCIe device;
faulty system board.
Install the NVRAM_CLR
jumper and restart the
system. See Figure 6-1 for
jumper location. If the
problem persists, see
"Troubleshooting Expansion
Cards" on page 187.
Read fault
Requested sector
not found
The operating system cannot
read from the hard drive or
USB device, the system could
not find a particular sector on
the disk, or the requested
sector is defective.
Replace the USB medium or
device. Ensure that the USB
or hard drive cables are
properly connected. See
"Troubleshooting a USB
Device" on page 165, or
"Troubleshooting a Hard
Drive" on page 181 for the
appropriate drive(s) installed
in your system.
Remote
configuration
update attempt
failed
System unable to process
Remote Configuration
request.
Retry Remote Configuration.
Table 1-6.
System Messages
(continued)
Message
Causes
Corrective Actions