Yamaha DSP5D Owner's Manual - Page 120
Controlling the graphic EQ from the DCA In the DISPLAY ACCESS repeatedly
![]() |
View all Yamaha DSP5D manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 120 highlights
15 Graphic EQ and Parametric EQ 2 Click the / buttons at the left and right of the MODULE box to select the GEQ module you want to operate. At this time make sure that the GEQ ON/OFF button is on. Also make sure that the corresponding module is inserted into an appropriate channel, and that insertin/out is enabled for that channel. Hint • The upper part of the GEQ PARAM screen functions as a spectrum analyzer. If a signal is being input to the corresponding channel, the level of each frequency band is displayed in realtime. • As an alternate way to select the desired GEQ module, you can use the GEQ ASSIGN screen (GEQ function) (➥ p.173). 3 Click the GEQ button located in the upper middle of the screen to select the 31-band graphic EQ. 4 If desired, use the buttons of the LIMIT area to specify the variable range of the faders. The LIMIT area lets you select the maximum amount and direction of the change controlled by the faders. You can select ±15 dB/±12 dB/±6 dB (both boost and cut directions) or -24 dB (cut only). 5 Drag the faders in the lower part of the screen to adjust the amount of boost/cut. The value of each fader is shown by the box below it. Hint Clicking the EQ FLAT button below the LIMIT area will reset all faders to 0 dB. Controlling the graphic EQ from the DCA section Here's how to control the graphic EQ using the keys and faders of the panel DCA strip. In this case, the corresponding graphic EQ is divided into six regions for control. 1 In the DISPLAY ACCESS section, repeatedly press the [GEQ] key to access the GEQ PARAM screen. GEQ PARAM GEQ/PEQ button MODULE box EQ ON/OFFbutton 2 Click the / buttons at the left and right of the MODULE box to select the GEQ module you want to operate. At this time, make sure that the GEQ ON/OFF button is turned on. Also make sure that the corresponding module is inserted into an appropriate channel, and that insert is enabled for that channel. Hint When the GEQ PARAM screen is displayed, pressing the [SEL] key of a channel in which a GEQ module is inserted will recall the corresponding GEQ module in the screen. 3 Click the GEQ button located in the upper middle of the screen to select the 31-band graphic EQ. 4 Use the buttons of the LIMIT area to select the maximum amount and direction of the change controlled by the faders. 5 In the lower part of the screen, click a button in the ASSIGN TO FADERS area to select the region you will control from the DCA faders. The buttons in the ASSIGN TO FADERS area correspond to the following frequency regions. A 20.0-100 button The eight bands 20.0 Hz-100 Hz B 63.0-315 button The eight bands 63.0 Hz-315 Hz C 200-1.00k button The eight bands 200 Hz-1.00 kHz D 630-3.15k button The eight bands 630 Hz-3.15 kHz E 2.00k-10.0k button The eight bands 2.00 kHz-10.0 kHz F 4.00k-20.0k button The eight bands 4.00 kHz-20.0 kHz When a button is clicked, you can use the DCA faders to control the faders of that frequency region. The faders of the selected region are indicated by a red line in the center of the fader. While any of the buttons in the ASSIGN TO FADERS area is on, you can use the FADER MODE section FADER MODE [A]-[F] keys to select the frequency region corresponding to these buttons. Even if all of the buttons in the ASSIGN TO FADERS area are off, you can hold down the [SHIFT] key and press one of the FADER MODE [A]-[F] keys to select the region to be controlled by the DCA faders. 4.00kHz-20.0kHz 2.00kHz-10.0kHz 20.0Hz-100Hz 63.0Hz-315Hz 630Hz-3.15kHz 200Hz-1.00kHz ASSIGN TO FADERS area LIMIT area 120 PM5D/PM5D-RH V2 / DSP5D Owner's Manual Operating section
![](/manual_guide/products/yamaha-dsp5d-owners-manual-81b84d8/120.png)