Yamaha DSP5D Owner's Manual - Page 78

8 Input Patch / Output Patch operations Patching the insert-out and insert-in Here we will explain how to make insert connections, using an example in which an external device connected to an AD/DA card in a slot is inserted into an input channel. However, the procedure is the same when inserting into an output channel, the only difference being that you will be working in a screen for output channels. 1 In the DISPLAY ACCESS section, press the INPUT [PATCH] key several times to access the INSERT PATCH screen (INPUT PATCH function) shown below. In the left side of this screen you can select an output port to use as insert-out, and in the right side of the screen you can select an input port to use as insert-in. INSERT PATCH 3 In the right side of the screen, click the grid at which the input port connected to your external device intersects the desired channel. You can select the following input ports. AD IN 1-48 AD ST IN 1-4 SLOT IN 1-4 FX OUT 1-8 GEQ OUT 1-12 2TR IN D1-D3 2TR IN A1/A2 INPUT jacks 1-48 ST IN jacks 1-4 (L/R) Input channels of an I/O card installed in slots 1-4 Outputs (L/R) of internal effects 1-8 Outputs of GEQ modules 1-12 2TR IN DIGITAL jacks 1-3 (L/R) 2TR IN ANALOG jacks 1/2 (L/R) The SELECTED PATCH area shows the channel corresponding to the grid at which the cursor is located. To the right of this are shown the input/output ports patched to insert-out/insert-in for this channel. If you want to insert into an output channel, press the OUTPUT [PATCH] key several times to access the OUTPUT PATCH function INSERT PATCH screen. 2 In the left side of the screen, click the grid at which the output port connected to your external device intersects the desired channel. The procedure is the same as in the INPUT PATCH screen or OUTPUT PATCH screen. You can select the following output ports. MIX OUT 1-24 SLOT OUT 1-4 FX IN 1-8 GEQ IN 1-12 2TR OUT 1-3 MIX OUT jacks 1-24 Output channels of an I/O card installed in slots 1-4 L/R inputs of internal effects 1-8 Inputs of GEQ modules 1-12 2TR OUT DIGITAL jacks 1-3 (L/R) Hint If you select GEQ IN at the left side of the screen, the identically-numbered GEQ OUT will be automatically selected at the right side of the screen, inserting the correspondinglynumbered GEQ module into that channel. (For details on using the graphic EQ ➥ p.118) Channel at which the cursor is located Port patched to Port patched to insert-out insert-in Hint To move the cursor rapidly between the grids in the left and right sides of the screen, you can hold down the [SHIFT] key and press the CURSOR [√]/[®] keys. Note With the steps you have taken so far, the external device has been patched to the insert-out/insert-in of the selected channel. However, please note that the insert connection is not actually enabled until you turn on the INSERT I/O ON/OFF button in the INSERT/DIRECT OUT screen as described below. As an exception to this, the INSERT I/O ON/OFF button is automatically turned on if you patch a GEQ. 4 Press the INPUT [PATCH] key several times to access the INSERT/DIRECT OUT POINT screen (INPUT PATCH function) shown below. In the INSERT/DIRECT OUT POINT screen (INPUT PATCH function) you can switch insert on/off for each input channel. In this screen you can also select the insert I/O point (the location at which the external device will be inserted). INSERT/DIRECT OUT POINT If you want to insert into an output channel, press the OUTPUT [PATCH] key several times to access the OUTPUT PATCH function INSERT PATCH screen. 78 PM5D/PM5D-RH V2 / DSP5D Owner's Manual Operating section