Yamaha DSP5D Owner's Manual - Page 193

Information shown in the display Function menu Global functions Output functions 5 4 D BANK SELECT Of the four banks, select the bank for which you want to make settings. When you use the A-D buttons to select a bank, the name of that bank will be displayed in the field immediately above. You can click the button at the left to edit the name of the bank. E CLEAR BANK This button erases the currently selected bank (all MIDI messages will be deleted). 6 8 7 F MIDI message From the top, these fields assign MIDI messages to the ENCODER [ON] keys, encoders, CH [ON] keys, and faders. Click the to open the MIDI REMOTE SETUP window, and input the message as hexadecimal values. You can input the following values. Value 00(H)- FF(H) END SW ENC FAD Available Assignments Content All The MIDI message that is transmitted (hexadecimal). Indicates the end of the MIDI message. When you operate the All corresponding controller, the MIDI message from the begin- ning until immediately before END will be transmitted. Indicates the on/off status of the encoder [ON] key or the channel [ON] key. A value of 7F(H) is transmitted when the key turns All on, and a value of 00(H) is transmitted when the key turns off. If this is assigned to an ENCODER or FADER, the current value of the key will be transmitted when the encoder or fader is operated. ENCODER ON/ ENCODER Indicates the current position of the encoder. If assigned to an ENCODER, a value of 00-7F(H) is transmitted when the encoder is operated. If assigned to an ENCODER [ON] key, the current value of the encoder is transmitted when the key is switched on. CH ON/ FADER Indicates the current position of the fader. If assigned to a FADER, a value of 00-7F(H) is transmitted when the fader is operated. If assigned to a CH [ON] key, the current value of the fader is transmitted when the key is switched on. Hint When you click a hexadecimal value, the region interpreted as a MIDI message that includes that value will be displayed in red. G LEARN Use this button to assign a received MIDI message to a controller. When you turn on one of the four LEARN buttons, the MIDI message received by the PM5D will be assigned to the corresponding controller. The LEARN function uses the MIDI messages received at the input port specified by the MIDI REMOTE OUTPUT PORT in the MIDI SETUP screen. Hint • MIDI messages assigned using the LEARN button can be a maximum of 16 bytes long (the 17th and subsequent bytes are discarded). If the message is less than 16 bytes long, END will be immediately after the last data value. • If a control change is received, the third byte will automatically be replaced by FAD (if the assignment destination is FADER), ENC (if the assignment destination is ENCODER), or SW (if the assignment destination is ENCODER ON or CH ON). • If more than one message is received while a LEARN button is on, the last message will be used. (If the status byte was omitted from the last message, the appropriate status byte will be added.) H LATCH If a specific byte is set to "SW" in a message assigned to an ENCODER [ON] key or CH [ON] key, use the LATCH button to select one of the following behaviors. • If the LATCH button is on The on/off status will change each time you press the key (Latched). If you press the key from the Off state, a MIDI message with 7F(H) as the SW value will be transmitted, and when you press the same key once again a MIDI message with 00(H) as the SW value will be transmitted. • If the LATCH button is off The switch will be on only while you are holding it down, and will turn off when you release it (Unlatched). Immediately after you press the key, a MIDI message with 7F(H) as the SW value will be transmitted; immediately after you release the key, a MIDI message with a SW value of 00(H) will be transmitted. If a specific byte is set to "ENC" (or "FAD") in a message assigned to an ENCODER [ON] key or a CH [ON] key, use the LATCH button to select one of the following behaviors. • If the LATCH button is on If you press the key from the Off state, a MIDI message with the current setting of the encoder (or fader) as the ENC (or FAD) value will be transmitted, and when you press the same key once again a MIDI message with a value of 00(H) as the ENC (or FAD) value will be transmitted. • If the LATCH button is off The moment you press the key, a MIDI message with the current setting of the encoder (or fader) as the ENC (or FAD) value will be transmitted; the moment you release the key, a MIDI message with 00(H) as the ENC (or FAD) value will be transmitted. Note If SW/ENC/FAD is not specified as the last byte of the MIDI message, turning the key on or off will transmit the same MIDI message; i.e., the same message is transmitted when the key goes off. Input functions Appendices PM5D/PM5D-RH V2 / DSP5D Owner's Manual Reference section 193