Yamaha DSP5D Owner's Manual - Page 332
Delay, Multi Filter, Freeze
![]() |
View all Yamaha DSP5D manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 332 highlights
Effects Parameters ❏ DELAY→REV One input, two output delay and reverb effects in series. Parameter DELAY L DELAY R FB. DLY FB. GAIN DELAY HI HPF LPF DLY.BAL REV TIME INI. DLY REV HI DIFF. DENSITY SYNC NOTE L NOTE R NOTE FB Range 0.0-1000.0 ms 0.0-1000.0 ms 0.0-1000.0 ms -99 to +99% 0.1-1.0 THRU, 21.2 Hz- 8.00 kHz 50.0 Hz-16.0 kHz, THRU 0-100% 0.3-99.0 s 0.0-500.0 ms 0.1-1.0 0-10 0-100% OFF/ON *1 *1 *1 Description Left channel delay time Right channel delay time Feedback delay time Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) Delay high-frequency feedback ratio High-pass filter cutoff frequency Low-pass filter cutoff frequency Delay and delayed reverb balance (0% = all delayed reverb, 100% = all delay) Reverb time Initial delay before reverb begins High-frequency reverb time ratio Spread Reverb density Tempo parameter sync on/off Used in conjunction with TEMPO to determine left channel DELAY L Used in conjunction with TEMPO to determine right channel DELAY R Used in conjunction with TEMPO to determine FB. DLY *1. (Maximum value depends on the tempo setting) ❏ DIST→DELAY One input, two output distortion and delay effects in series. Parameter DST TYPE DRIVE MASTER TONE N. GATE DELAY FB. GAIN HI. RATIO FREQ. DEPTH DLY.BAL SYNC DLY.NOTE MOD.NOT E Range DST1, DST2, OVD1, OVD2, CRUNCH 0-100 0-100 -10 to +10 0-20 0.0-2725.0 ms -99 to +99% 0.1-1.0 0.05-40.00 Hz 0-100% 0-100% OFF/ON *1 *2 Description Distortion type (DST = distortion, OVD = overdrive) Distortion drive Master volume Tone control Noise reduction Delay time Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback) High-frequency feedback ratio Modulation speed Modulation depth Distortion and delay balance (0% = all distortion, 100% = all delayed distortion) Tempo parameter sync on/off Used in conjunction with TEMPO to determine DELAY Used in conjunction with TEMPO to determine FREQ. *1. (Maximum value depends on the tempo setting) *2. ❏ MULTI FILTER Two input, two output 3-band multi-filter (24 dB/octave). Parameter Range TYPE 1 HPF, LPF, BPF TYPE 2 HPF, LPF, BPF TYPE 3 FREQ. 1 FREQ. 2 FREQ. 3 LEVEL 1 LEVEL 2 LEVEL 3 RESO. 1 RESO. 2 RESO. 3 HPF, LPF, BPF 28.0 Hz-16.0 kHz 28.0 Hz-16.0 kHz 28.0 Hz-16.0 kHz 0-100 0-100 0-100 0-20 0-20 0-20 Description Filter 1 type: high pass, low pass, band pass Filter 2 type: high pass, low pass, band pass Filter 3 type: high pass, low pass, band pass Filter 1 frequency Filter 2 frequency Filter 3 frequency Filter 1 level Filter 2 level Filter 3 level Filter 1 resonance Filter 2 resonance Filter 3 resonance ❏ FREEZE One input, one output basic sampler. Parameter Range REC MODE MANUAL, INPUT REC DLY -1000 to +1000 ms TRG LVL -60 to 0 dB TRG MASK 0-1000 ms PLY MODE MOMENT, CONTI., INPUT START END LOOP LOOP NUM START [SAMPLE] END [SAMPLE] LOOP [SAMPLE] PITCH FINE *1 1 1 0-100 0-262000 0-262000 0-262000 -12 to +12 semitones -50 to +50 cents MIDI TRG OFF, C1-C6, ALL Description In MANUAL mode, recording is started by pressing the REC and PLAY buttons. In INPUT mode, Record-Ready mode is engaged by pressing the REC button, and actual recording is triggered by the input signal. Recording delay. For plus values, recording starts after the trigger is received. For minus values, recording starts before the trigger is received. Input trigger level (i.e., the signal level required to trigger recording or playback) Once playback has been triggered, subsequent triggers are ignored for the duration of the TRG MASK time. In MOMENT mode, the sample plays only while the that the PLAY button is pressed. In CONT mode, playback continues once the PLAY button has been pressed. The number of times the sample plays is set using the LOOP NUM parameter. In INPUT mode, playback is triggered by the input signal. Playback start point in milliseconds Playback end point in milliseconds Loop start point in milliseconds Number of times the sample plays Playback start point in samples Playback end point in samples Loop start point in samples Playback pitch shift Playback pitch shift fine PLAY button can be triggered by using MIDI Note on/off messages. *1. 0.0-5941.0 ms (fs=44.1 kHz), 0.0 ms-5458.3 ms (fs=48 kHz), 0.0- 2970.5 ms (fs=88.2 kHz), 0.0 ms-2729.2 ms (fs=96 kHz) 332 PM5D/PM5D-RH V2 / DSP5D Owner's Manual Reference section
![](/manual_guide/products/yamaha-dsp5d-owners-manual-81b84d8/332.png)