Yamaha DSP5D Owner's Manual - Page 49
Various operations for input channels, Selecting the function of the encoders
![]() |
View all Yamaha DSP5D manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 49 highlights
Various operations for input channels Selecting the function of the encoders Exchanging the fader and encoder When the PM5D is in the default state, the encoders of the functions INPUT channel strip and ST IN/FX RTN channel strip are assigned to control send levels to MIX buses 1-24. However you can use the various ENCODER MODE keys to select one of the following as the function of the encoders. Key Encoder function Display You can use the FADER [FLIP] key to exchange the functions assigned to the faders and encoders of the channel strip. For example with the default setting (FADER [FLIP] key off), the faders control the input channel input levels, and MIX SEND SELECT [1]-[24] keys Send levels to MIX buses 1-24 1-24 the encoders control the send levels to the MIX buses. If you then press the FADER [FLIP] key to make the LED [PAN] key Pan (balance) Pn light, the faders will control the send levels to the MIX 5 [GAIN/ATT] key Head amp input sensitivity HA buses and the encoders will control the input channel [GAIN/ATT] key Attenuator input levels. At [ALT LAYER] key Input level for the currently unselected layer*1 AL *1. In the INPUT channel strip, the CH 1-24 layer and the CH 25-48 layer are in a "front/rear" relation. In the ST IN/FX RTN channel strip, the ST IN 1-4 layer and the FX RTN 1-4 layer are in a "front/rear" relation. Control the send level and on/off status of the signal sent from the channel to the MIX buses Control the channel input level and on/off status Input channel operations The currently selected function is shown by the key that is lit and by the encoder mode indicator. Repeatedly pressing the [PAN] key or [ALT LAYER] key will alternate between the function selected by that key and the MIX bus send level. Repeatedly pressing the [GAIN/ ATT] key will alternate between the following three choices; input sensitivity to the internal head amp → attenuator → MIX bus send level. Hint If the FADER section [FLIP] key is on, the functions controlled by the encoders and faders will be exchanged. ➠ Control the channel input level and on/off status Control the send level and on/off status of the signal sent from the channel to the MIX buses The function assigned to the controls when the [FLIP] key is on (LED lit) will depend on the current encoder mode as follows. [FLIP] key Off On Encoder mode MIX SEND PAN GAIN/ATT ALT LAYER MIX SEND PAN GAIN/ATT ALT LAYER Encoder Send level from channel to MIX bus Pan (balance) Head amp input sensitivity / attenuator Channel (currently unselected layer) input level Channel (currently selected layer) input level Pan of the signal sent from channels (of the currently selected layer) to paired MIX buses (invalid if MIX channels are not paired) Head amp input sensitivity / attenuator Send level from channel (currently un-selected layer) to MIX bus Function of each control ENCODER [ON] key Fader On/off status of signal sent from channel to MIX bus On/off status of signal sent from channel to STEREO bus No function Channel (currently selected layer) input level Channel (currently unselected layer) on/off Channel (currently selected layer) on/off Channel (currently selected layer) on/off No function Send level from channel (currently selected layer) to MIX bus On/off status of signal sent from channel (currently unselected layer) to MIX bus CH [ON] key Channel (currently selected layer) on/off On/off status of signal sent from channel (currently selected layer) to MIX bus Note The DCA channel strip and STEREO A/B channel strip are not affected by the on/off status of the [FLIP] key. PM5D/PM5D-RH V2 / DSP5D Owner's Manual Operating section 49
![](/manual_guide/products/yamaha-dsp5d-owners-manual-81b84d8/49.png)