Yamaha DSP5D Owner's Manual - Page 21
DSP5D front panel, WORD CLOCK IN/OUT connectors
View all Yamaha DSP5D manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 21 highlights
DSP5D front panel 1 2 Note 2 • You should use a CAT5 STP (Shielded Twisted Pair) cable to prevent electromagnetic interference. • DSP5D Editor and the DME-N Network driver required for connection with your computer can be downloaded from the Yamaha website listed below. http://www.yamahaproaudio.com/ Top, front, and rear panels CASCADE IN OUT IN 75Ω TERMINATED OUT IN OUT IN TX RX TX RX 3 4 5 67 OUT IN 75Ω TERMINATED OUT IN OUT IN TX RX TX RX JK 8 9L M A INPUT jacks 1-48 / ST IN (stereo input) jacks 1-4 These are balanced XLR-3-31 type input jacks for inputting analog audio signals from line level devices or microphones. The nominal input level is -62 dBu to +10 dBu. A resettable head amp is provided on all jacks, and head amp settings can be stored in scene memory. B OMNI OUT jacks 1-24 These are XLR-3-32 (balanced) jacks for outputting analog audio signals. These are used mainly for outputting the MIX/MATRIX/STEREO A/B channel signals. The nominal output level is +4 dBu. Note The nominal output level of OMNI OUT jacks 1-24 is +4 dBu (maximum level is +24 dBu), but if necessary, this can be changed to -2 dBu (maximum level +18 dBu) by setting an internal switch (a fee will be charged). For details, please contact your Yamaha dealer. C CASCADE IN/OUT connectors These are D-sub half-pitch 68-pin female connectors to allow connection of the DSP5D, PM5D, DCU5D, and DME64N so that audio signals and control signals can be transmitted and received. D NETWORK connector This connector allows the DSP5D to be connected to a Windows computer via a CAT5 Ethernet cable. This is used mainly when remotely controlling or editing the DSP5D from the dedicated "DSP5D Editor" application software. E WORD CLOCK IN/OUT connectors These are BNC connectors used to input and output word clock signals from and to an external device. The input connector is terminated with 75 ohms. F CASCADE IN/OUT connectors These are RJ-45 connectors that can be connected via a CAT5 Ethernet cable to a DSP5D or DCU5D so that audio signals and control signals can be transmitted and received. Note • As connectors, use RJ-45 connectors that are compatible with Neutrik's EtherCon®. • As cables, you should use CAT5 STP cables (shielded twisted pair cables) to prevent electromagnetic interference. • To prevent electromagnetic interference, use conductive tape etc. to firmly fasten the metal portion of the connector to the shield of the cable. • These connectors use EtherSound technology, but are only for use with the PM5D system; they cannot be connected to other EtherSound equipment. For details on the length of cables that can be used, refer to the following website. http://www.ethersound.com/technology/compatibility.php G IN/OUT [TX]/[RX] LED When signals are transmitted (TX) or received (RX) via the [CASCADE IN]/[CASCADE OUT] connectors, the corresponding LED will light. When you use the rear panel mode switch to set the machine ID, the number of LEDs corresponding to the machine ID number will light for five seconds (➥ p.153). H SLOT 1-2 The input/output ports can be expanded by installing separately sold mini-YGDAI I/O cards in these slots. I DC POWER INPUT connector A separately sold PW800W power supply can be connected here as an external backup power supply. Use a power supply link cable (PSL360) to make this connection. J POWER LED This will light if power is being supplied to the DSP5D. K POWER switch This switch turns the power on/off. L AC IN connector Use the included power cable to supply power to this connector. M Grounding screw For safe operation, be sure that the DSP5D is correctly grounded. The included power cable has a three-pin plug, and if the AC outlet is grounded, the DSP5D will be grounded appropriately. If the AC outlet you're using is not grounded, you must be sure to connect this screw to a valid electrical ground. Correct grounding will effectively eliminate noises such as hum and interference. PM5D/PM5D-RH V2 / DSP5D Owner's Manual Operating section 21