Yamaha DSP5D Owner's Manual - Page 306
SEND LEVEL, PRE/POST Send level / Send, point, LEVEL COPY [ALL CH x ALL MIX]
View all Yamaha DSP5D manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 306 highlights
PAN/ROUTING function B SEND LEVEL, PRE/POST (Send level / Send point) Select one of the following two parameters to view in the grid. ❏ When the SEND LEVEL button is on The send levels of the signals sent from input channels to MIX buses are shown in the grid as bar graphs. Except for the fact that the send-sources are input channels and the send-destinations are MIX buses, the bar graph display is the same as in the MIX to MATRIX VIEW screen (MATRIX/ST function) (➥ p.264). Depending on the send location of the signal being sent to the MIX bus, the color of the bar graph will differ as follows. (green) . . . . PRE EQ (immediately before the EQ) (yellow) . . . PRE FADER (immediately before the fader) (blue) . . . . . POST ON (immediately after the [ON] key) or POST TO ST (immediately after the [TO ST] key) To edit the send level of a signal, move the cursor to the grid where the desired channel and MIX bus intersect, and turn the [DATA] encoder. To switch a MIX send on/off, click the grid where the desired channel and MIX bus intersect. If the SEND LEVEL button is on, you can select a desired grid and copy its send level (pan) value to other channels (horizontal direction) or to other MIX buses (vertical direction), or switch all grids on/off simultaneously. To do so, move the cursor to the desired grid; then hold down the [SHIFT] key and press the [ENTER] key. (Alternatively, hold down the [SHIFT] key and click the desired grid.) When the following window appears, select one of the following choices to copy, and click the OK button. LEVEL COPY [ALL MIX ] Copy the send level (pan) value of the selected grid to all MIX buses. LEVEL COPY [ALL CH ] Copy the send level (pan) value of the selected grid to all input channels. LEVEL COPY [ALL CH x ALL MIX] Copy the send level (pan) value of the selected grid to all input channels / all MIX buses. ALL OFF [ALL MIX ] Turn off the signals sent from the specified input channel to all MIX buses. ALL ON [ALL MIX ] Turn on the signals sent from the specified input channel to all MIX buses. ALL OFF [ALL CH ] Turn off the signals sent from all input channels to the specified MIX bus. ALL ON [ALL CH ] Turn on the signals sent from all input channels to the specified MIX bus. ALL OFF [ALL CH x ALL MIX] Turn off the signals sent from all input channels to all MIX buses. ALL ON [ALL CH x ALL MIX] Turn on the signals sent from all input channels to all MIX buses. ❏ When the PRE/POST button is on This screen shows the send positions of the signals sent from the input channels to the MIX buses. Each indication has the following significance. (green) . . . PRE EQ (immediately before the EQ) (yellow) . . PRE FADER (immediately before the fader) (gray) . . . . POST ON (immediately after the [ON] key) (red) . . . . . POST TO ST (immediately after the [TO ST] key) To change the send position of a signal, move the cursor to the grid where the desired channel and MIX bus intersect, and press the [ENTER] key, or click, or turn the [DATA] encoder. If the PRE/POST button is on, the send position for all grid locations can be changed simultaneously. To do so, hold down the [SHIFT] key and click the desired grid. (Alternatively, move the cursor to the desired grid; then hold down the [SHIFT] key and press the [ENTER] key.) When the following window appears, select one of the following choices and click the OK button. 306 PM5D/PM5D-RH V2 / DSP5D Owner's Manual Reference section