Yamaha DSP5D Owner's Manual - Page 171
INSERT Insert destination, GEQ/PEQ button, EQ ON/OFF button, LIBRARY, Level meter, SLOW/FAST
View all Yamaha DSP5D manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 171 highlights
Information shown in the display Function menu Global functions Output functions C INSERT (Insert destination) Selects the location at which the GEQ module will be inserted. Move the cursor to this box and turn the [DATA] encoder or click the / buttons at left or right to display the desired insertion destination, and then press the [ENTER] key to finalize the change. You can choose the following insertion destinations. • INS CH1-INS CH48 Input channel 1-48 insert in/out • INS STIN1 (L/R)-INS STIN4 (L/R) ST IN channel 1-4 (L/R) insert in/out • INS MIX1-INS MIX24 MIX channel 1-24 insert in/out • INS MTRX1-INS MTRX8 MATRIX channel 1-8 insert in/out • INS ST A (L/R) STEREO A channel (L/R) insert in/out • INS ST B (L/R) STEREO B channel (L/R) insert in/out • INS MON (L/R/C) (PM5D only) MONITOR channel (L/R/C) insert in/out Note • When you select the insertion destination here, insert in/out will be patched simultaneously, and insertion will automatically be turned on for the channel into which the graphic EQ module was inserted. • If you move the cursor away without pressing the [ENTER] key, the setting will revert to its original state. D GEQ/PEQ button This switches between the 31-band graphic EQ (GEQ) and 8-band parametric EQ (PEQ). Note Even if you switch between GEQ and PEQ, the graphic EQ and parametric EQ parameters will remember their settings from before the change. E EQ ON/OFF button Switches the currently selected GEQ module on/off. F LIBRARY This button accesses the GEQ LIBRARY screen. G Level meter This meter indicates the peak level before and after the GEQ module. ❏ When graphic EQ is selected 89 J K L M N OP H SLOW/FAST Switches the fall speed of the spectrum analyzer between slow or fast. This setting does not affect the meters in other screens or the meters on the panel. I PEAK HOLD Switches the peak hold function on/off for the spectrum analyzer. The peak level for each band is held while this button is on. (To reset the peak level display, turn this button off and then on again). This setting does not affect the meters in other screens or the meters on the panel. J Spectrum analyzer This is an analyzer that shows a realtime level display for each band of the input signal. K EQ graph Indicates the current frequency response of the graphic EQ. L Faders These faders cut/boost the frequency bands of the graphic EQ. The actual values are shown in the numerical boxes below. M ASSIGN TO FADERS These buttons divide the 31 bands of the graphic EQ into six groups so that you can use the DCA faders to adjust the boost/cut amount of each band. Click one of the six buttons A (20.0-100), B (63.0-315), C (2001.00k), D (630-3.15k), E (2.00k-10.0k), F (4.00k20.0k). DCA faders 1-8 will be assigned to the corresponding region of frequency bands, allowing you to control them with the DCA faders. At this time, the divisions of the corresponding faders and the value in the numerical box screen will turn red in the screen. To return to the original state, press the DCA (OFF) button in the screen or the [DCA] button on the panel. Note • If the ASSIGN TO FADERS buttons A-F are off, you can hold down the [SHIFT] button on the panel and press a FADER MODE section button [A]-[F], and then use the DCA faders to control the corresponding region of the graphic EQ in the same way as if you had pressed a button A-F in the screen. • The currently selected DCA fader mode (DCA, A-F) is disabled while one of the ASSIGN TO FADERS buttons A-F is on. At this time, you can also use the FADER MODE section buttons [A]-[F] to switch between regions of the graphic EQ; the button for the selected region will blink, and the remaining buttons will light. • If the AUTO ASSIGN button is off, the setting in the ASSIGN TO FADERS field is cleared automatically when you switch screens, and the currently selected DCA fader mode will once again be enabled. Input functions Appendices PM5D/PM5D-RH V2 / DSP5D Owner's Manual Reference section 171