Yamaha DSP5D Owner's Manual - Page 203
Controlling DME parameters, In the DME CONTROL screen, choose SETUP
View all Yamaha DSP5D manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 203 highlights
Information shown in the display Function menu Global functions Output functions 6 In the OUTPUT PORT field located in the lower right of the screen, select the PM5D port that will transmit audio signals to the DME. The types of port that can be selected here will depend on the port that is currently selected for cascade output (MIXER SETUP screen CASCADE OUT PORT SELECT field), as follows. Setting in the CASCADE OUT PORT SELECT field (MIXER SETUP screen) CASCADE OUT SLOT3/4 SLOT1-4 [CH1-8] SLOT1-4 [CH9-16] Items available in the OUTPUT PORT field ----, SLOT1-SLOT4 ----, SLOT1-SLOT4, CASCADE OUT Note • You cannot switch the cascade output port setting from the DME CONTROL screen. If necessary, click the MIXER SETUP button to access the MIXER SETUP screen (SYS/ W.CLOCK function), and change the port you will use for cascade output. • Depending on the type of cascade connection, the DSP5D port will indicate only the items that can be selected: ---, SLOT1-2, CASCADE OUT (D-SUB), or CASCADE OUT (RJ-45). 7 If you want scene changes on the PM5D to be linked with scene changes on the DME series unit, turn on the MIDI PGM CHANGE button in the center of the screen. If the MIDI PGM CHANGE button is on, switching the scene on the PM5D will cause a program change message of a number corresponding to that scene to be sent to the DME. Hint • The above program change message is always transmitted via the I/O card or the CASCADE IN/OUT connector. This is not affected by MIDI PGM CHANGE or by the MIDI program change transmission port or transmission on/off setting selected in the MIDI SETUP screen. • The program number assignment for each scene can be specified in the MIDI PGM CHANGE screen. 8 To initiate communication between the PM5D and the DME series unit, click the CONNECT button to turn it on. While the CONNECT button is on, parameter operations and scene store/recall operations on the DME can be remotely controlled from the PM5D. To terminate communication, click the CONNECT button once again to turn it off. ❏ Controlling DME parameters Here's how the parameters of the DME series unit can be controlled from the PM5D. If desired, the changes you make can be saved in the scene of the DME series unit. 1 In the DME CONTROL screen, choose SETUP, and turn on the CONNECT button to initiate communication. 2 In the upper left of the screen, use the component type / component selection areas to select the component you want to control. If a component other than SETUP is selected, internal parameters of the DME can be controlled from the PM5D screen. The following illustration is an example of when the SLOT OUTPUT component is selected. 3 Use the knobs, sliders, and buttons in the screen to control the parameters of the DME series unit. Knob, slider, and button operation methods are the same as for the PM5D's internal parameters. For details on the parameters that can be operated for each component, refer to the owner's manual of the DME series unit. 4 If you want to use DCA faders 1-8 to control the parameters of the component, click an A-F button in the ASSIGN TO FADERS area. When you click a button A-F, the corresponding parameters will be assigned to DCA faders 1-8, and can be controlled by the faders. To return to the previous state, click the DCA button. Hint As an alternative to clicking the A-F buttons, you can obtain the same result by holding down the top panel [SHIFT] key and pressing the [A]-[F] keys of the FADER MODE section. 5 If you want to store your changes in a scene of the DME series unit, use the SCENE field in the upper right of the screen to select the storedestination, and click the STORE button. The edited settings will be stored as a scene in the DME. To recall this scene, use the SCENE field in the upper right of the screen to select the scene, and click the RECALL button. Note When storing a DME scene from the PM5D's screen, you can only store by overwriting an existing scene on the DME; you cannot store the settings as a new scene or edit the scene name. Hint For a system in which only the DSP5D and DME are connected, use DSP5D Editor to specify the DSP5D port that will be connected to the DME. You can select the following connectors/slots for each port. • INPUT PORT CASCADE IN (D-SUB), SLOT1, SLOT2, CASCADE OUT (RJ-45) • OUTPUT PORT CASCADE OUT (D-SUB), SLOT1, SLOT2, CASCADE OUT (RJ-45) Input functions Appendices PM5D/PM5D-RH V2 / DSP5D Owner's Manual Reference section 203