Sharp AR M162 AR-M162 AR-M207 Operation Manual Suite - Page 231
Recall Setting Busy, Recall Set Err
View all Sharp AR M162 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 231 highlights
KEY OPERATOR PROGRAMS RECALL SETTING (BUSY) This program is used to set the number of recall attempts and the interval between recall attempts when a transmission is not successful due to the line being busy or other reason. Normally the machine is set to make 2 recall attempts at intervals of 3 minutes. If you do not wish to have recalling take place, set the number of attempts to "0" (steps 6 and 7). 1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 94). 2 Select "SENDING FUNCTION" with the [ ] or [ ] key and then press the [OK] key. 3 Select "RECALL SETTING (BUSY)" with the [ ] or [ ] key and then press the [OK] key. If you do not wish to change the recall interval setting, go to step 6. 4 Select "RECALL INTERVAL" with the [ ] or [ ] key and then press the [OK] key. 5 Enter the recall interval (01 to 15) with the numeric keys and then press the [OK] key. • The recall interval can be set from 1 to 15 minutes. • After finishing step 5, if you do not wish to change the number of recall attempts, press the [BACK] key to exit. 6 Select "RECALL TIMES" with the [ ] or [ ] key and then press the [OK] key. 7 Enter the number of recall attempts with the numeric keys and then press the [OK] key. • The number of recall attempts can be set in each country are shown in the following table. Country Differentiation Table The number of recall attempts United Kingdom 0 to 10 Australia and New Zealand 0 to 9 • If you do not wish to have recalling take place, set the number of attempts to "0". Note • If you made a mistake in step 5 or step 7, move the cursor to the mistake with the [ ] or [ ] key and enter the correct number. • Even if this setting is enabled, the machine will not re-attempt the call when a fax is sent by manual transmission. RECALL SET (ERR) When sending a fax, this setting is used to select whether or not the machine will automatically re-attempt the call if the transmission fails due to a line error. Normally the machine is set to make 1 recall attempt at intervals of 1 minute. If you do not wish to have recalling take place, set the number of attempts to "0" (steps 6 and 7). 1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 94). 2 Select "SENDING FUNCTION" with the [ ] or [ ] key and then press the [OK] key. 3 Select "RECALL SET(ERR)" with the [ ] or [ ] key and then press the [OK] key. If you do not wish to change the recall interval setting, go to step 6. 4 Select "RECALL INTERVAL" with the [ ] or [ ] key and then press the [OK] key. 5 Enter the recall interval (00 to 15) with the numeric keys and then press the [OK] key. • The recall interval can be set from 0 to 15 minutes. • After finishing step 5, if you do not wish to change the number of recall attempts, press the [BACK] key to exit. 6 Select "RECALL TIMES" with the [ ] or [ ] key and then press the [OK] key. 7 Enter the number of recall attempts with the numeric keys and then press the [OK] key. • The number of recall attempts can be set in each country are shown in the following table. Country Differentiation Table The number of recall attempts United Kingdom 0 to 5 Australia and New Zealand 0 to 1 • If you do not wish to have recalling take place, set the number of attempts to "0". Note • If the recall interval is set to "0", the machine will immediately call again after the connection is broken due to the line error. • If you made a mistake in step 5, move the cursor to the mistake with the [ ] or [ ] keys and enter the correct number. • Even if this setting is enabled, the machine will not re-attempt the call when a fax is sent by manual transmission. 102