D-Link 3324SRi Reference Manual - Page 109

xStack Gigabit Layer 3 Switch Command Line Interface Manual

12

B

ROADCAST

S

TORM

C

ONTROL

C

OMMANDS

The broadcast storm control commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters)

in the following table.

Command

Parameters

config traffic control

[<storm_grouplist> | all] {broadcast [enable | disable] | multicast

[enable | disable] | dlf [enable | disable] | threshold <value 0-255>}

{group_list <storm_grouplist>}

show traffic control

Each command is listed, in detail, in the following sections.

config traffic control

Purpose

Used to configure broadcast/multicast traffic control.

Syntax

config traffic control [<storm_grouplist> | all] {broadcast

[enable | disable] | multicast [enable | disable] | dlf [enable |

disable] | threshold <value 0-255>}

Description

This command is used to configure broadcast storm control.

Parameters

<storm_grouplist>

−

Used to specify a broadcast storm control

group. This is specified by listing the lowest switch number and

the beginning port number on that switch, separated by a colon.

Then the highest switch number, and the highest port number of

the range (also separated by a colon) are specified. The beginning

and end of the port list range are separated by a dash. For

example, 1:3 specifies switch number 1, port 3. 2:4 specifies

switch number 2, port 4. 1:3-2:4 specifies all of the ports between

switch 1, port 3 and switch 2, port 4

−

in numerical order.

all

−

Specifies all broadcast storm control groups on the Switch.

broadcast [enable | disable]

−

Enables or disables broadcast

storm control.

multicast [enable | disable]

−

Enables or disables multicast storm

control.

dlf [enable | disable]

−

Enables or disables dlf traffic control.

threshold <value 0-255>

−

The upper threshold at which the

specified traffic control is switched on. The

<value>

is the number

of broadcast/multicast/dlf packets, in kilopackets per second

(Kpps), received by the Switch that will trigger the storm traffic

control measures.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To configure traffic control and enable broadcast storm control system wide:

101

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 109

Broadcast Storm Control Commands, config traffic control

Page 109 highlights