D-Link 3324SRi Reference Manual - Page 67

xStack Gigabit Layer 3 Switch Command Line Interface Manual

DGS-3324SRi:4#ping 10.48.74.121 times 4

Command: ping 10.48.74.121

Reply from 10.48.74.121, time<10ms




Ping statistics for 10.48.74.121

Packets: Sent =4, Received =4, Lost =0

DGS-3324SRi:4#

traceroute

Purpose

Used to trace the routed path between the Switch and a destination

endstation.

Syntax

traceroute <ipaddr> {ttl <value 1-60> | port <value 30000-64900>

| timeout <sec 1-65535> | probe <value <1-9>}

Description

The traceroute command allows you to trace a route between the

Switch and a give host on the network.

Parameters

<ipaddr>

- Specifies the IP address of the host.

ttl <value 1-60>

- The time to live value of the trace route request.

This is the maximum number of routers the traceroute command will

cross while seeking the network path between two devices.

port <value 30000-64900> -

The port number. Must be above

1024.The value range is from 30000 to 64900.

timeout <sec 1-65535>

- Defines the time-out period while waiting

for a response from the remote device. The user may choose an

entry between 1 and 65535 seconds.

probe <value 1-9>

- The probe value is the number of times the

Switch will send probe packets to the next hop on the intended

traceroute path. The default is 1.

Restrictions

None.

Example usage:

To trace the routed path between the Switch and 10.48.74.121.

DGS-3324SRi:4#traceroute 10.48.74.121

probe 3

Command: traceroute 10.48.74.121

probe 3

1

<10ms 10.254.254.251

2

<10ms 10.55.25.35

3

<10ms 10.22.35.1

DGS-3324SRi:4#

59

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 67

traceroute, Packets: Sent =4, Received =4, Lost =0 - router

Page 67 highlights