D-Link 3324SRi Reference Manual - Page 62

xStack Gigabit Layer 3 Switch Command Line Interface Manual

8

S

WITCH

U

TILITY

C

OMMANDS

The switch utility commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the

following table. Please note that commands concerning the CompactFlash card (cfg_fromCf, firmware_to CF, etc.) are specific

to the DGS-3324SRi only.

Command

Parameters

download

[firmware_fromTFTP <ipaddr> <path_filename 64> image_id <int

1-2> {unit [all | <unitid 1-12>]} | cfg_fromTFTP <ipaddr>

<path_filename 64> {increment} | firmware_fromCF <path_filename

64> image_id <int 1-2> | cfg_fromCF <path_filename 64>

{increment}]

upload

[cfg_toTFTP <ipaddr> <path_filename 64> | log_toTFTP <ipaddr>

<path_filename 64> | [ firmware_toCF <path_filename 64>

image_id <int 1-2> | cfg_toCF <path_filename 64> | log_toCF

<path_filename 64>]

show

firmware_information

config firmware

image_id

<int 1-2> [delete | boot_up]

ping

<ipaddr> {times <value 1-255>} {timeout <sec 1-99>}

traceroute

<ipaddr> {ttl <value 1-60> | port <value 30000-64900> | timeout

<sec 1-65535> | probe <value <1-9>

Each command is listed, in detail, in the following sections.

download

Purpose

Used to download and install new firmware or a switch

configuration file from a TFTP server or a CompactFlash memory

card.

Syntax

download [ firmware_fromTFTP <ipaddr> <path_filename 64>

image_id <int 1-2> {unit [all | <unitid 1-12>]} | cfg_fromTFTP

<ipaddr> <path_filename 64> {increment} | firmware_fromCF

<path_filename 64> image_id <int 1-2> | cfg_fromCF

<path_filename 64> {increment} ]

Description

This command is used to download a new firmware or a switch

configuration file from a TFTP server or a CompactFlash memory

card.

Parameters

firmware_fromTFTP

−

Download and install new firmware on the

Switch from a TFTP server.

firmware_fromCF

−

Download and install new firmware on the

Switch from a CompactFlash server.

cfg_fromTFTP -

Download a switch configuration file from a TFTP

server.

cfg_fromCF -

Download a switch configuration file from a CF

server.

±

image_id <int 1-2>-

This Switch holds two places for

54

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 62

Switch Utility Commands, download

Page 62 highlights