D-Link 3324SRi Reference Manual - Page 142

xStack Gigabit Layer 3 Switch Command Line Interface Manual

DGS-3324SRi:4#show link_aggregation

Link Aggregation Algorithm = MAC-source-dest

Command: show link_aggregation

Group ID

: 1

Master Port

: 2:17

Member Port

: 1:5-1:10,2:17

Active Port:

Status

: Disabled

Flooding Port

: 1:5

DGS-3324SRi:4

config lacp_port

Purpose

Used to configure settings for LACP compliant ports.

Syntax

config lacp_port <portlist> mode [active | passive]

Description

This command is used to configure ports that have been

previously designated as LACP ports (see create

link_aggregation).

Parameters

<portlist>

−

Specifies a range of ports to be configured. The port

list is specified by listing the lowest switch number and the

beginning port number on that switch, separated by a colon. Then

the highest switch number, and the highest port number of the

range (also separated by a colon) are specified. The beginning

and end of the port list range are separated by a dash.

For

example, 1:3 specifies switch number 1, port 3. 2:4 specifies

switch number 2, port 4.

1:3-2:4 specifies all of the ports between

switch 1, port 3 and switch 2, port 4

−

in numerical order.

mode

– Select the mode to determine if LACP ports will initially

send LACP control frames.

Restrictions

Only administrator-level users can issue this command.

±

±

active

– Active LACP ports are capable of processing and

sending LACP control frames. This allows LACP compliant

devices to negotiate the aggregated link so the group may be

changed dynamically as needs require. In order to utilize the

ability to change an aggregated port group, that is, to add or

subtract ports from the group, at least one of the participating

devices must designate LACP ports as active. Both devices

must support LACP.

passive

– LACP ports that are designated as passive

cannot initially send LACP control frames, uless the port

receives LACP frames. In order to allow the linked port group

to negotiate adjustments and make changes dynamically, at

one end of the connection must have “active” LACP ports

(see above).

Example usage:

To configure LACP port mode settings:

134

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 142

config lacp_port, Link Aggregation Algorithm = MAC-source-dest

Page 142 highlights