D-Link 3324SRi Reference Manual - Page 35

xStack Gigabit Layer 3 Switch Command Line Interface Manual

config ports

one connection is set for

1000 master

, the other side of the

connection must be set for

1000 slave

. Any other configuration will

result in a link down status for both ports.

flow_control [enable | disable]

– Enable or disable flow control for

the specified ports.

learning [enable | disable]

−

Enables or disables the MAC address

learning on the specified range of ports.

state [enable | disable]

−

Enables or disables the specified range

of ports.

description <desc 32>

- Enter an alphanumeric string of no more

than 32 characters to describe a selected port interface.

clear

– Enter this command to clear the port description of the

selected port(s).

Restrictions

Only administrator-level users can issue this command.

Example usage:

To configure the speed of port 3 of unit 1 to be 10 Mbps, full duplex, learning and state enable:

DGS-3324SRi:4#config ports 1:1-1:3 speed 10_full learning enable state

enable

Command: config ports 1:1-1:3 speed 10_full learning enable state

enable

Success.

DGS-3324SRi:4#

show ports

Purpose

Used to display the current configuration of a range of ports.

Syntax

show ports <portlist> {description}

Description

This command is used to display the current configuration of a

range of ports.

Parameters

<portlist>

−

Specifies a range of ports to be displayed. The port

list is specified by listing the lowest switch number and the

beginning port number on that switch, separated by a colon. Then

the highest switch number, and the highest port number of the

range (also separated by a colon) are specified. The beginning

and end of the port list range are separated by a dash. For

example, 1:3 specifies switch number 1, port 3.

2:4 specifies

switch number 2, port 4. 1:3-2:4 specifies all of the ports between

switch 1, port 3 and switch 2, port 4

−

in numerical order.

{description} – Adding this parameter to the command will allow

the user to view previously configured descriptions set on various

ports on the Switch.

Restrictions

None.

27

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 35

config ports, show ports - d link dgs

Page 35 highlights