D-Link 3324SRi Reference Manual - Page 286

xStack Gigabit Layer 3 Switch Command Line Interface Manual

Route Source

Metric

RIP

0 to 16777214

mettype 1

mettype 2

Static

0 to 16777214

mettype 1

mettype 2

Local

0 to 16777214

mettype 1

mettype 2

Metric Type

Allowed Metric Type combinations are

mettype 1

or

mettype 2

. The metric value

0

above will be redistributed in OSPF as the

metric

20

.

Example Usage:

To add route redistribution settings:

DGS-3324SRi:4#create route redistribute dst ospf src rip

Command: create route redistribute dst ospf src rip

Success.

DGS-3324SRi:4#

create route redistribute dst rip src

Purpose

Used to add route redistribution settings for the exchange of OSPF

routes to RIP routes on the Switch.

Syntax

create route redistribute dst rip src {all | internal | external |

type_1 | type_2 | inter+e1 | inter+e2}] {metric <value>}

Description

This command will redistribute routing information between the

OSPF and RIP routing protocols to all routers on the network that

are running OSPF or RIP. Routing information entered into the

Static Routing Table on the local xStack switch is also redistributed

Parameters

src {all | internal | external | type_1 | type_2 | inter+e1 | inter+e2}

−

Allows the selection of the protocol of the source device. The user

may choose between:

•

external

- Specifies the external protocol of the source device.

•

all

– Specifies both internal an external.

•

internal

– Specifies the internal protocol of the source device.

•

type_1

- Calculates the metric (for RIP to OSPF) by adding the

destination’s interface cost to the metric entered in the Metric

field.

•

type_2

- Uses the metric entered in the Metric field without

change. This field applies only when the destination field is

OSPF.

•

inter+e1

– Specifies the internal protocol AND type 1 of the

external protocol.

•

inter+e2

– Specifies the internal protocol AND type 2 of the

278

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 286

create route redistribute dst rip src, mettype 1

Page 286 highlights