D-Link 3324SRi Reference Manual - Page 153

xStack Gigabit Layer 3 Switch Command Line Interface Manual

19

IGMP S

NOOPING

C

OMMANDS

The IGMP Snooping commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the

following table.

Command

Parameters

config igmp_snooping

[<vlan_name 32> | all] {host_timeout <sec 1-16711450> |

router_timeout <sec 1-16711450> | leave_timer <sec 1-

16711450> | state [enable | disable] | fast_leave [enable |

disable]}

[<vlan_name 32> | all] {query_interval <sec 1-65535> |

max_response_time <sec 1-25> | robustness_variable <value 1-

255> | last_member_query_interval <sec 1-25> | state [enable |

disable]}

{forward_mcrouter_only}

disable igmp_snooping

{forward_mcrouter_only}

config router_ports

<vlan_name 32> [add | delete] <portlist>

config

router_ports_forbidden

<vlan_name 32> [add | delete] <portlist>

show router_ports

{<vlan_name 32>} {static | dynamic | forbidden}

show igmp_snooping

{vlan<vlan_name 32>}

{vlan <vlan_name 32>}

{vlan <vlan_name 32>}


querier

enable igmp_snooping

show igmp_snooping

group

show igmp_snooping

forwarding

Each command is listed, in detail, in the following sections.


Purpose

Used to configure IGMP snooping on the Switch.

Syntax

config igmp_snooping [<vlan_name 32> | all] {host_timeout

<sec 1-16711450> | router_timeout <sec 1-16711450> |

leave_timer <sec 1-16711450> | state [enable | disable]

fast_leave [enable | disable]}

Description

This command allows you to configure IGMP snooping on the

Switch.

Parameters

<vlan_name 32>

−

The name of the VLAN for which IGMP

snooping is to be configured.

all

– Selecting this parameter will configure IGMP snooping for all

VLANs on the Switch.

host_timeout <sec 1-16711450>

−

Specifies the maximum

amount of time a host can be a member of a multicast group

without the Switch receiving a host membership report. The

default is 260 seconds.

router_timeout <sec 1-16711450>

−

Specifies the maximum

145

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 153

IGMP Snooping Commands, config igmp_snooping

Page 153 highlights