D-Link 3324SRi Reference Manual - Page 150

xStack Gigabit Layer 3 Switch Command Line Interface Manual

config igmp

25> | robustness_variable <value 1-255> |

last_member_query_interval <value 1-25> | state [enable |

disable]}

Description

This command allows you to configure IGMP on the Switch.

Parameters

<ipif_name 12>

−

The name of the IP interface for which you

want to configure IGMP.

all

−

Specifies all the IP interfaces on the Switch.

version <value 1-3>

−

Select the IGMP version number.

query_interval <sec 1-31744>

−

The time in seconds between

general query transmissions, in seconds.

max_response_time <sec 1-25>

−

Enter the maximum time in

seconds that the Switch will wait for reports from members.

robustness_variable <value 1-255>

−

This value states the

permitted packet loss that guarantees IGMP.

last_member_query_interval <value 1-25>

−

The Max Response

Time inserted into Group-Specific Queries and Group-and-

Source specific queries sent in response to Leave Group

messages, and is also the amount of time between Group-

Specific Query and Group-and-Source specific query messages.

The default is 1 second.

state [enable | disable]

−

Enables or disables IGMP for the

specified IP interface.

Restrictions

Only administrator-level users can issue this command.

Example Usage:

To configure the IGMPv3 for all IP interfaces.

DGS-3324SRi:4#config igmp all version 3 state enable

Command: config igmp all version 3 state enable

Success.

DGS-3324SRi:4#

show igmp

Purpose

Used to display the IGMP configuration for the Switch of for a

specified IP interface.

Syntax

show igmp {ipif <ipif_name 12>}

Description

This command will display the IGMP configuration for the Switch

if no IP interface name is specified. If an IP interface name is

specified, the command will display the IGMP configuration for

that IP interface.

Parameters

<ipif_name 12>

−

The name of the IP interface for which the

IGMP configuration will be displayed.

142

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 150

config igmp, show igmp, Time inserted into Group-Specific Queries and Group-and

Page 150 highlights