D-Link 3324SRi Reference Manual - Page 227
Packet Content, Control Lists for the Switch.
![]() |
UPC - 790069256042
View all D-Link 3324SRi manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 227 highlights
xStack Gigabit Layer 3 Switch Command Line Interface Manual Due to a chipset limitation, the Switch currently supports a maximum of 8 access profiles, each containing a maximum of 100 rules − with the additional limitation of 100 rules total for all 8 access profiles. Access profiles allow you to establish criteria to determine whether or not the Switch will forward packets based on the information contained in each packet's header. These criteria can be specified on a VLAN-by-VLAN basis. Creating an access profile is divided into two basic parts. First, an access profile must be created using the create access_profile command. For example, if you want to deny all traffic to the subnet 10.42.73.0 to 10.42.73.255, you must first create an access profile that instructs the Switch to examine all of the relevant fields of each frame: create access_profile ip source_ip_mask 255.255.255.0 profile_id 1 Here we have created an access profile that will examine the IP field of each frame received by the Switch. Each source IP address the Switch finds will be combined with the source_ip_mask with a logical AND operation. The profile_id parameter is used to give the access profile an identifying number − in this case, 1. The deny parameter instructs the Switch to filter any frames that meet the criteria − in this case, when a logical AND operation between an IP address specified in the next step and the ip_source_mask match. The default for an access profile on the Switch is to permit traffic flow. If you want to restrict traffic, you must use the deny parameter. Now that an access profile has been created, you must add the criteria the Switch will use to decide if a given frame should be forwarded or filtered. Here, we want to filter any packets that have an IP source address between 10.42.73.0 and 10.42.73.255: config access_profile profile_id 1 add access_id 1 ip source_ip 10.42.73.1 port 1:1 deny Here we use the profile_id 1 which was specified when the access profile was created. The add parameter instructs the Switch to add the criteria that follows to the list of rules that are associated with access profile 1. For each rule entered into the access profile, you can assign an access_id that both identifies the rule and establishes a priority within the list of rules. A lower access_id gives the rule a higher priority. In case of a conflict in the rules entered for an access profile, the rule with the highest priority (lowest access_id) will take precedence. The ip parameter instructs the Switch that this new rule will be applied to the IP addresses contained within each frame's header. source_ip tells the Switch that this rule will apply to the source IP addresses in each frame's header. Finally, the IP address 10.42.73.1 will be combined with the source_ip_mask 255.255.255.0 to give the IP address 10.42.73.0 for any source IP address between 10.42.73.0 to 10.42.73.255. Upon this release, the Xstack family of switches have encorporated four ways of creating access profile entries on the Switch which include Ethernet (MAC Address), IP, Packet Content and the most recent IPv6. Due to the present complexity of the access profile commands, it has been decided to split this command into four pieces to be better understood by the user and therefore simpler for the user to configure. The beginning of this section displays the create access_profile and config access_profile commands in their entirety. The following table divides these commands up into the defining features necessary to properly configure the access profile. Remember these are not the total commands but the easiest way to implemet Access Control Lists for the Switch. Command Parameters create access_profile config access_profile profile_id [ethernet {vlan | source_mac | destination_mac | 802.1p | ethernet_type} profile_id } [add access_id [ethernet {vlan | source_mac | destination_mac | 802.1p | ethernet_type } port [permit {priority {replace_priority} | replace_dscp } | deny] delete ] 219
![](/manual_guide/products/dlink-3324sri-reference-manual-364694b/227.png)