D-Link 3324SRi Reference Manual - Page 211

xStack Gigabit Layer 3 Switch Command Line Interface Manual

show 802.1x auth_configuration

and transmitting directions, or just the receiving direction.

Port Control: ForceAuth/ForceUnauth/Auto

−

Shows the

administrative control over the port’s authorization status. ForceAuth

forces the Authenticator of the port to become Authorized.

ForceUnauth forces the port to become Unauthorized.

QuietPeriod

−

Shows the time interval between authentication failure

and the start of a new authentication attempt.

TxPeriod

−

Shows the time to wait for a response from a supplicant

(user) to send EAP Request/Identity packets.

MaxReq

−

Shows the maximum number of times to retry sending

packets to the supplicant.

SuppTimeout

−

Shows the time to wait for a response from a

supplicant (user) for all EAP packets, except for the Request/Identity

packets.

ServerTimeout

−

Shows the length of time to wait for a response from

a RADIUS server.

ReAuthPeriod

−

Shows the time interval between successive re-

authentications.

ReAuthenticate: Enabled/Disabled

−

Shows whether or not to re-

authenticate.

Parameters

ports <portlist>

−

Specifies a range of ports. The port list is specified

by listing the lowest switch number and the beginning port number on

that switch, separated by a colon. Then the highest switch number,

and the highest port number of the range (also separated by a colon)

are specified. The beginning and end of the port list range are

separated by a dash. For example, 1:3 specifies switch number 1,

port 3. 2:4 specifies switch number 2, port 4. 1:3-2:4 specifies all of

the ports between switch 1, port 3 and switch 2, port 4

−

in numerical

order.

all

– denotes all ports on the Switch.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To display the 802.1x authentication states (stacking disabled):

DGS-3324SRi:4#show 802.1x auth_configuration ports 1:1

Command: show 802.1x auth_configuration ports 1:1

802.1X

: Enabled

Authentication Mode

: Port_based

Authentication Protocol

: Radius_EAP

Port number

: 1:1

Capability

: None

AdminCrlDir

: Both

OpenCrlDir

: Both

Port Control

: Auto

QuietPeriod

: 60

sec

TxPeriod

: 30

sec

203

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 211

show 802.1x auth_configuration, Authentication Mode

Page 211 highlights