D-Link 3324SRi Reference Manual - Page 93

xStack Gigabit Layer 3 Switch Command Line Interface Manual

DGS-3324SRi:4#config stp priority 4096 instance_id 2

Command : config stp priority 4096 instance_id 2

Success.

DGS-3324SRi:4#

config stp mst_config_id

Purpose

Used to update the MSTP configuration identification.

Syntax

config stp mst_config_id {revision_level <int 0-65535> | name

<string>

Description

This command will uniquely identify the MSTP configuration

currently configured on the Switch. Information entered here will

be attached to BDPU packets as an identifier for the MSTP region

to which it belongs. Switches having the same

revision_level

and

name

will be considered as part of the same MSTP region.

Parameters

revision_level <int 0-65535>

– Enter a number between 0 and

65535 to identify the MSTP region. This value, along with the

name will identify the MSTP region configured on the Switch. The

default setting is

0

.

name <string>

- Enter an alphanumeric string of up to 32

characters to uniquely identify the MSTP region on the Switch.

This

name

, along with the

revision_level

value will identify the

MSTP region configured on the Switch. If no

name

is entered, the

default name will be the MAC address of the device.

Restrictions

Only administrator-level users can issue this command.

Example usage:

To configure the MSTP region of the Switch with

revision_level

10 and the

name

“Trinity”:

DGS-3324SRi:4#config stp mst_config_id revision_level 10 name Trinity

Command : config stp mst_config_id revision_level 10 name Trinity

Success.

DGS-3324SRi:4#

config stp mst_ports

Purpose

Used to update the port configuration for a MSTP instance.

Syntax

config stp mst_ports <portlist> instance_id <value 0-15>

{internalCost [auto | <value 1-20000000>] `priority <value 0-

240>}

Description

This command will update the port configuration for a STP

instance_id

. If a loop occurs, the MSTP function will use the port

priority to select an interface to put into the forwarding state. Set a

85

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 93

config stp mst_config_id, config stp mst_ports

Page 93 highlights