D-Link 3324SRi Reference Manual - Page 68

xStack Gigabit Layer 3 Switch Command Line Interface Manual

9

N

ETWORK

M

ONITORING

C

OMMANDS

The network monitoring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in

the following table.

Command

Parameters

show packet ports

<portlist>

show error ports

<portlist>

show utilization

[ports | cpu]

clear counters

ports <portlist>

clear log

show log

index <value_list>

enable syslog

disable syslog

show syslog

create syslog host

[<index 1-4> | all ] {severity [informational | warning | all] | facility

[local0 | local1 | local2 | local3 | local4 | local5 | local6 | local7] |

udp_port <udp_port_number> | ipaddress <ipaddr> | state [enable

| disable]}

config syslog host

<index 1-4> {severity [informational | warning | all] | facility [local0 |

local1 | local2 | local3 | local4 | local5 | local6 | local7] | udp_port

<udp_port_number> | ipaddress <ipaddr> | state [enable |

disable]}

config syslog host all

{severity [informational | warning | all] | facility [local0 | local1 |

local2 | local3 | local4 | local5 | local6 | local7] | udp_port

<udp_port_number> | state [enable | disable]}

delete syslog host

[<index 1-4> | all]

show syslog host

[<index 1-4>]

config

system_severity

[trap | log | all] [critical | warning | information]

show system_severity

Each command is listed, in detail, in the following sections.

show packet ports

Purpose

Used to display statistics about the packets sent and received by

the Switch.

Syntax

show packet ports <portlist>

Description

This command is used to display statistics about packets sent and

received by ports specified in the port list. The results are

separated into three tables, labeled

A

,

B

, and

C

in the window

above. Table

A

is relevant to the size of the packets, Table

B

is

relevant to the type of packets and Table

C

is relevant to the type

60

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 68

Network Monitoring Commands, show packet ports

Page 68 highlights