Home » D-Link Manuals » Hubs & Switches » D-Link 3324SRi » Manual Viewer

D-Link 3324SRi Reference Manual - Page 9

Introduction, Accessing the Switch via the Serial Port - dgs configuration

UPC - 790069256042

Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

xStack Gigabit Layer 3 Switch Command Line Interface Manual 1 INTRODUCTION The Switch can be managed through the Switch's serial port, Telnet, or the Web-based management agent. The Command Line Interface (CLI) can be used to configure and manage the Switch via the serial port or Telnet interfaces. This manual provides a reference for all of the commands contained in the CLI for members of the xStack family, including the DGS-3324SRi, DGS-3324SR, DXS-3326GSR and the DXS-3350SR. Examples present in this manual may refer to any member of the xStack family and may show different port counts, but are universal to this series of switches, unless otherwise stated. Configuration and management of the Switch via the Web-based management agent is discussed in the User's Guide. Accessing the Switch via the Serial Port The Switch's serial port's default settings are as follows: • 115200 baud • no parity • 8 data bits • 1 stop bit A computer running a terminal emulation program capable of emulating a VT-100 terminal and a serial port configured as above is then connected to the Switch's serial port via an RS-232 DB-9 cable. With the serial port properly connected to a management computer, the following screen should be visible. If this screen does not appear, try pressing Ctrl+r to refresh the console screen. Figure 1-1. Initial CLI screen There is no initial username or password. Just press the Enter key twice to display the CLI input cursor − DGS-3324SRi:4#. This is the command line where all commands are input. 1

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

Match case Limit results 1 per page

xStack Gigabit Layer 3 Switch Command Line Interface Manual

NTRODUCTION

The Switch can be managed through the Switch’s serial port, Telnet, or the Web-based management agent. The Command Line

Interface (CLI) can be used to configure and manage the Switch via the serial port or Telnet interfaces.

This manual provides a reference for all of the commands contained in the CLI for members of the xStack family, including the

DGS-3324SRi, DGS-3324SR, DXS-3326GSR and the DXS-3350SR. Examples present in this manual may refer to any member

of the xStack family and may show different port counts, but are universal to this series of switches, unless otherwise stated.

Configuration and management of the Switch via the Web-based management agent is discussed in the User’s Guide.

Accessing the Switch via the Serial Port

The Switch’s serial port’s default settings are as follows:

•

115200 baud

•

no parity

•

8 data bits

•

1 stop bit

A computer running a terminal emulation program capable of emulating a VT-100 terminal and a serial port configured as

above is then connected to the Switch’s serial port via an RS-232 DB-9 cable.

With the serial port properly connected to a management computer, the following screen should be visible. If this screen does

not appear, try pressing Ctrl+r to refresh the console screen.

Figure 1-1.

Initial CLI screen

There is no initial username or password. Just press the

Enter

key twice to display the CLI input cursor

−

DGS-3324SRi:4#

This is the command line where all commands are input.