D-Link 3324SRi Reference Manual - Page 252

xStack Gigabit Layer 3 Switch Command Line Interface Manual

2.

CS’s must change their role to CaS and then to MS, to become a MS of a SIM group. Thus the CS cannot directly be

converted to a MS.

3.

The user can manually configure a CS to become a CaS.

4.

A MS can become a CaS by:

a.

Being configured as a CaS through the CS.

b.

If report packets from the CS to the MS time out.

5.

The user can manually configure a CaS to become a CS

6.

The CaS can be configured through the CS to become a MS.

After configuring one switch to operate as the CS of a SIM group, additional switches may join the group by manually

configuring the Switch to be a MS. The CS will then serve as the in band entry point for access to the MS. The CS’s IP address

will become the path to all MS’s of the group and the CS’s Administrator’s password, and/or authentication will control access

to all MS’s of the SIM group.

With SIM enabled, the applications in the CS will redirect the packet instead of executing the packets. The applications will

decode the packet from the administrator, modify some data, then send it to the MS. After execution, the CS may receive a

response packet from the MS, which it will encode and send it back to the administrator.

When a CaS becomes a MS, it automatically becomes a member of the first SNMP community (include read/write and read

only) to which the CS belongs. However if a MS has its own IP address, it can belong to SNMP communities to which other

switches in the group, including the CS, do not belong.

The D-Link Single IP Management commands in the Command Line Interface (CLI) are listed (along with the appropriate

parameters) in the following table.

Command

Parameters

enable sim

disable sim

show sim

{[candidates {<candidate_id 1-100>} | members {<member_id

1-32>} | group {commander_mac <macaddr>} | neighbor]}

reconfig

{member_id <value 1-32> | exit}

config sim_group

[add <candidate_id 1-100> {<password>} | delete

<member_id 1-32>]

config sim

[{[commander {group_name <groupname 64> | candidate] |

dp_interval <sec 30-90> | hold_time <sec 100-255>}

download sim_ms

[firmware_from_tftp | configuration_from_tftp] <ipaddr>

<path_filename> {[members <mslist 1-32> | all}}

upload sim_ms

configuration_to_tftp

<ipaddr> <path_filename> <member_id 1-32>

Each command is listed, in detail, in the following sections.

enable sim

Purpose

Used to enable Single IP Management (SIM) on the Switch

Syntax

enable sim

Description

This command will enable SIM globally on the Switch. SIM features

and functions will not function properly unless this function is

244

Section	Page
Introduction	9
	9
	9
Accessing the Switch via the Serial Port	9
Setting the Switch’s IP Address	10
Using the Console CLI	12
	12
	12
Connecting to the Switch	12
Command Syntax	17
Basic Switch Commands	19
Switch Port Commands	34
Port Security Commands	37
Network Management (SNMP) Commands	40
Switch Utility Commands	62
Network Monitoring Commands	68
Multiple Spanning Tree Protocol (MSTP) Commands	85
Forwarding Database Commands	99
Broadcast Storm Control Commands	109
QoS Commands	111
Port Mirroring Commands	124
VLAN Commands	128
Link Aggregation Commands	138
IP Commands (Including IP Multinetting)	144
IGMP Commands (Including IGMP v3)	149
IGMP Snooping Commands	153
MAC Notification Commands	163
Access Authentication Control Commands	168
SSH Commands	193
SSL Commands	201
802.1X Commands	207
Access Control List (ACL) Commands	226
Traffic Segmentation Commands	244
Stacking Commands	247
D-Link Single IP Management Commands	251
Time and SNTP Commands	262
ARP Commands	269
VRRP Commands	273
Routing Table Commands	281
Route Redistribution Commands	285
BOOTP Relay Commands	292
DNS Relay Commands	296
RIP Commands	300
DVMRP Commands	303
PIM Commands	308
IP Multicasting Commands	312
MD5 Configuration Commands	314
OSPF Configuration Commands	317
Route Preference Commands	338
Jumbo Frame Commands	342
File System Commands	344
Command History List	352

D-Link 3324SRi Reference Manual - Page 252

Used to enable Single IP Management SIM on the Switch, enable sim

Page 252 highlights